Rating:
Information washer, adjusting Denso
Include in ##:
Number on scheme 052-01H
09600-04980
as WASHER, ADJUSTING
Cross reference number
Part num
Firm num
Firm
Name
09656-90430
WASHER, ADJUSTING
Information:
Warning Signs and Labels
There may be several specific warning signs on your engine. Please familiarize yourself with all warning signs.Make sure that you can read all warning signs. Clean or replace warning signs if you cannot read the words or see the pictures. When cleaning the labels use a cloth, water and soap. Do not use solvents, gasoline, etc., to clean warning signs. The use of solvents, gasoline, etc., could loosen the sign's adhesive and cause the sign to fall off.You must replace a warning sign if it is damaged, missing or cannot be read. If a warning sign is attached to a part, and that part is replaced, make sure a new warning sign is installed on the replaced part. See your Caterpillar dealer for new warning signs.Do not operate or work on the engine unless you have read and understand the instructions and warnings in this Manual. Proper care is your responsibility. Failure to follow the instructions or heed the warnings could result in injury or death.
The clutch warning sign is located on the clutch housing (if equipped).
Clutch warning sign.
Rotating gears- finger or hand entanglement. Do not service until reading the operator's manual.
Located near batteries (if equipped):
Improper jumper cable connections can cause an explosion resulting in personal injury.Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual.
Located on the mounting base (if equipped) near the lifting holes:
Improper lift rigging can allow load to tumble causing injury and damage.
Located on the fuel tank (if equipped):
Drain fuel tank before lifting unit. Lifting this unit when fuel is present in the tank could result in separation of the tank from the base and cause personal injury or death.
Located on engine lifting eye cover assembly.
Do not use the engine lifting eyes to remove the engine and generator together.
Located on the side panels of the generator (if equipped):
Do not connect generator to a utility electrical distribution system unless it is isolated from the system. Electrical feedback into the distribution system can occur and could cause personal injury or death.Open and secure main distribution system switch. Or if the connection is permanent, install a double throw transfer switch to prevent electrical feedback. Some generators are specifically approved by a utility to run in parallel with the distribution system and isolation may not be required. Always check with your utility as to the applicable circumstances.
Located on the outside of the control panel vandal door (if equipped):
Always operate this unit with the vandal door open. Operating the unit with the vandal door closed restricts access to the emergency stop button and could result in injury or death.
Located on the outside of the control panel vandal door (if equipped), above the emergency stop warning:
Do not operator or work on
There may be several specific warning signs on your engine. Please familiarize yourself with all warning signs.Make sure that you can read all warning signs. Clean or replace warning signs if you cannot read the words or see the pictures. When cleaning the labels use a cloth, water and soap. Do not use solvents, gasoline, etc., to clean warning signs. The use of solvents, gasoline, etc., could loosen the sign's adhesive and cause the sign to fall off.You must replace a warning sign if it is damaged, missing or cannot be read. If a warning sign is attached to a part, and that part is replaced, make sure a new warning sign is installed on the replaced part. See your Caterpillar dealer for new warning signs.Do not operate or work on the engine unless you have read and understand the instructions and warnings in this Manual. Proper care is your responsibility. Failure to follow the instructions or heed the warnings could result in injury or death.
The clutch warning sign is located on the clutch housing (if equipped).
Clutch warning sign.
Rotating gears- finger or hand entanglement. Do not service until reading the operator's manual.
Located near batteries (if equipped):
Improper jumper cable connections can cause an explosion resulting in personal injury.Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual.
Located on the mounting base (if equipped) near the lifting holes:
Improper lift rigging can allow load to tumble causing injury and damage.
Located on the fuel tank (if equipped):
Drain fuel tank before lifting unit. Lifting this unit when fuel is present in the tank could result in separation of the tank from the base and cause personal injury or death.
Located on engine lifting eye cover assembly.
Do not use the engine lifting eyes to remove the engine and generator together.
Located on the side panels of the generator (if equipped):
Do not connect generator to a utility electrical distribution system unless it is isolated from the system. Electrical feedback into the distribution system can occur and could cause personal injury or death.Open and secure main distribution system switch. Or if the connection is permanent, install a double throw transfer switch to prevent electrical feedback. Some generators are specifically approved by a utility to run in parallel with the distribution system and isolation may not be required. Always check with your utility as to the applicable circumstances.
Located on the outside of the control panel vandal door (if equipped):
Always operate this unit with the vandal door open. Operating the unit with the vandal door closed restricts access to the emergency stop button and could result in injury or death.
Located on the outside of the control panel vandal door (if equipped), above the emergency stop warning:
Do not operator or work on