Rating:
Information valve assy, suctio Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
8-98145455-1,genuine and SCV 294200-2760,294200-4760, 1460A056, 294009-0741,8-98145455-1 - (Color: 294200-4760)
Generic Color: 294200-4760
Generic Color: 294200-4760
Suction Control Valve SCV 294200-2760 294200-4760 294009-0740 8981454550 8981454530 Diesel Fuel injector Pump Regulator
xinDieseltt Symptoms of a failing SCV include inconsistent rail pressure readings, rough engine idle, increased fuel consumption, and potential stalling || Replacement Part Number:294200-2760 294200-4760 294009-0740 8981454550 8981454530 Check whether the part number is correct to avoid installing incorrect parts. || Our suction control valve comes with six-month warranty || Every SCV valve is rigorously tested and verified. || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you.
xinDieseltt Symptoms of a failing SCV include inconsistent rail pressure readings, rough engine idle, increased fuel consumption, and potential stalling || Replacement Part Number:294200-2760 294200-4760 294009-0740 8981454550 8981454530 Check whether the part number is correct to avoid installing incorrect parts. || Our suction control valve comes with six-month warranty || Every SCV valve is rigorously tested and verified. || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you.
Include in ##:
Number on scheme 033
29400-01122
as VALVE ASSY, SUCTIO
Cross reference number
Part num
Firm num
Firm
Name
29420-04760
VALVE ASSY, SUCTIO
Information:
1. Make a mark on compressor housing (1), cartridge assembly (3) and the turbine housing (4) for correct installation. 2. Loosen clamp assembly (2). Remove compressor housing (1) and cartridge assembly (3) from the turbine housing.3. Remove bolts (6) and plates (5) that hold cartridge assembly in the compressor housing. Remove cartridge assembly (3). 4. Remove O-ring seal (7) from the cartridge assembly. 5. Put cartridge assembly (3) in position in tooling (A) and loosen nut on the compressor wheel with tooling (C).6. Remove nut (8) and the compressor wheel (9). 7. Remove shaft and wheel assembly (10) from the cartridge assembly. 8. Remove shroud (11) from the cartridge assembly. 9. Remove four bolts (12) and then remove backplate (13) from the cartridge assembly.10. Remove spacer (14) from the backplate. 11. Remove two seal rings (15) from the spacer. 12. Remove snap ring (16) from cartridge housing with tool (B). 13. Remove bearing (17) and rings from the cartridge housing.14. Remove snap ring (18) from cartridge housing with tool (B). 15. Turn the cartridge housing over and then remove screws (20), plate (21) and collar (19). 16. Remove bearing (22) from the cartridge housing. 17. Remove snap ring (23) from the cartridge housing with tool (B).Assemble Turbocharger
Make sure all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Put clean engine oil on all parts of the cartridge assembly. 1. Install snap ring (1) in the cartridge housing with tool (A). Make sure the oil hole in plate (5) is open and clean to prevent a bearing failure.2. Install bearing (2), collars (3), plate (5) and screws (4). Tighten the screws to a torque of 2.5 N m (22 lb.in.). Install the rings that hold bearings in position with the round edges of the rings toward the bearings. 3. Turn the cartridge housing over. Install snap ring (6) in the cartridge housing with tool (A). Install bearing (7), ring (8) and ring (9) in the housing. Install snap ring (10) with tool (A). Put 6V2055 High Vacuum Grease in the grooves for seal rings (11) at assembly to one half or more of the depth of the groove all the way around the grooves. 4. Install seal rings (11) on spacer (12). 5. Install spacer (12) in the backplate.6. Put the backplate (13) in position on the cartridge housing and install the bolts that hold it. Tighten the bolts to a torque of 9.5 N m (84 lb.in.). 7. Put the shroud (14) in position on the cartridge housing. 8. Install shaft and wheel assembly (15) in the cartridge housing. 9. Put the cartridge assembly in position in tooling (B).10. Put a small amount of oil on the wheel face that will be under the nut.11. Put compressor wheel (17) in position on the shaft.
Do not put a side force on the shaft when the nut is tightened.
12. Install nut (16) and tighten it to a torque of 4
Make sure all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Put clean engine oil on all parts of the cartridge assembly. 1. Install snap ring (1) in the cartridge housing with tool (A). Make sure the oil hole in plate (5) is open and clean to prevent a bearing failure.2. Install bearing (2), collars (3), plate (5) and screws (4). Tighten the screws to a torque of 2.5 N m (22 lb.in.). Install the rings that hold bearings in position with the round edges of the rings toward the bearings. 3. Turn the cartridge housing over. Install snap ring (6) in the cartridge housing with tool (A). Install bearing (7), ring (8) and ring (9) in the housing. Install snap ring (10) with tool (A). Put 6V2055 High Vacuum Grease in the grooves for seal rings (11) at assembly to one half or more of the depth of the groove all the way around the grooves. 4. Install seal rings (11) on spacer (12). 5. Install spacer (12) in the backplate.6. Put the backplate (13) in position on the cartridge housing and install the bolts that hold it. Tighten the bolts to a torque of 9.5 N m (84 lb.in.). 7. Put the shroud (14) in position on the cartridge housing. 8. Install shaft and wheel assembly (15) in the cartridge housing. 9. Put the cartridge assembly in position in tooling (B).10. Put a small amount of oil on the wheel face that will be under the nut.11. Put compressor wheel (17) in position on the shaft.
Do not put a side force on the shaft when the nut is tightened.
12. Install nut (16) and tighten it to a torque of 4