Buy 29420-03670 VALVE ASSY, SUCTIO Denso Cross


Rating:
8
Buy VALVE ASSY, SUCTIO 29420-03670 genuine, new aftermarket engine parts with delivery

Information valve assy, suctio Denso

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$81.02

11 Apr 2025
0.1102[0.05] pounds
CN: NMGYYJZFS
Manifold Pressure Intake MAP Sensor 294200-0670 294200-3670 8-98181831-0 Fuel Pressure Regulator Suction Control Valve SCV/Fit for Isuzu 6HK1 Hino J08 Nissan Denso MAP Pressure Sensor
XCSZWTY Features & Quality Manifold air pressure sensor has high reliability and stability, long in working life with temperature compensation, high level of accuracy. || OE NO.294200-0670 294200-3670 8-98181831-0 || Part NO.294200-0670 || /Fit For Isuzu 6HK1 Hino J08 Nissan || Easy to install: You can replace parts by yourself, just need to remove the old parts, solve the vehicle problems by yourself, thus saving you a lot of money and time.
$113.16
 

07 Jan 2025
0.1102[0.05] pounds
CN: guangzhouyaoruoshang
294200-0670 294200-3670 8-98181831-0 Pressure Pump Suction Control Valve SCV 2942000670 For isuzu 6HK Hino J08 for nissan Denso
SouiiwbP 294200-0670 294200-3670 8-98181831-0 Pressure Pump Suction Control Valve SCV 2942000670 For isuzu 6HK Hino J08 for nissan Denso
$104.06
 

07 Jan 2025
0.1102[0.05] Pounds
CN: ZXJYBHD
294200-0670 294200-3670 8-98181831-0 Pressure Pump Suction Control Valve SCV 2942000670 For isuzu 6HK Hino J08 for nissan Denso
Xwency 294200-0670 294200-3670 8-98181831-0 Pressure Pump Suction Control Valve SCV 2942000670 For isuzu 6HK Hino J08 for nissan Denso

Cross reference number



Part num
Firm num
Firm
Name
29420-03670 
 
VALVE ASSY, SUCTIO




Information:

Start By:a. remove timing gear cover
Do not disconnect the air line from the air compressor governor until the air pressure is zero.
1. Loosen the bleed valves, and release the air pressure in the air tank. 2. Disconnect the lines from air compressor (1), and remove the air compressor. 3. Remove sleeve (2) from air compressor drive gear (3). 4. Remove the nut and washer that holds the air compressor drive gear to the air compressor. Use tooling (A) to remove air compressor drive gear (3) from the air compressor. 5. Remove nuts (4) and plate (5). Remove gear assembly (6) from the shaft. 6. If damaged, remove bearing (7) from gear assembly (6) with tooling (B) and a press. 7. Remove three nuts (8) and the washers from the adapter assembly studs.
Typical Example8. Remove adapter assembly (9) from the timing gear plate. 9. Remove shaft (10), O-ring seal (11) and sleeve (12) from the adapter assembly.Install Air Compressor And Accessory Drive
1. Install sleeve (12) into the adapter assembly.2. Install shaft (10) and O-ring seal (11) on the adapter assembly. 3. Put adapter assembly (9) in position on the timing gear plate. Fasten it with the three nuts and washers. 4. Install the bearing in gear assembly (6) with tooling (A) and a press. Install the bearing until it is 1.5 0.5 mm (.06 .02 in.) below the surface of the gear as shown. 5. Put gear assembly (6) in position on the shaft.6. Put plate (5) in position, and install three nuts (4) to hold it. 7. Put air compressor drive gear (3) in position on the air compressor shaft, and install the washer and nut (13). Tighten the nut to a torque of 200 25 N m (150 18 lb.ft.). Tap the gear with a hammer and tighten nut (13) again to a torque of 200 25 N m (150 18 lb.ft.). 8. Install sleeve (2) on gear (3). 9. Put a gasket in position on air compressor (1) and install the air compressor on the timing cover plate.End By:a. install timing gear cover

Have questions with 29420-03670?





Group cross 29420-03670

Back to top