Rating:
Information valve sub-assy, in Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$413.70
04 Oct 2021
0.0022[0.00] Pounds
CN: New WFAANW
WFAANW Common Rail Outlet Valve 090140-1200 090140-1350 090140-1990 090140-090140-2220 090140-1470 096420-0550 (Color : 090140 1990)
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
$413.70
04 Oct 2021
0.0022[0.00] Pounds
CN: New WFAANW
WFAANW Common Rail Outlet Valve 090140-1200 090140-1350 090140-1990 090140-090140-2220 090140-1470 096420-0550 (Color : 090140 2220)
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
$413.70
04 Oct 2021
0.0022[0.00] Pounds
CN: New WFAANW
WFAANW Common Rail Outlet Valve 090140-1200 090140-1350 090140-1990 090140-090140-2220 090140-1470 096420-0550 (Color : 096420 0550)
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
WFAANW HOW TO BUY || Our Company || Our products are multi-certified and quality guaranteed. If you have any questions, please contact us by email.
Include in ##:
Number on scheme 008
09010-05690
as VALVE SUB-ASSY, IN
Cross reference number
Part num
Firm num
Firm
Name
09014-01470
VALVE SUB-ASSY, IN
0901401470
22104-58230
TOYOTA
VALVE SUB-ASSY, IN
Information:
start by: a) remove fuel injection pump housing and governor1. Put the fuel injection pump housing on tool (A). 2. Remove bolts (1). 3. Remove bolt (2). Remove adapter housing (3) from the pump housing. 4. Remove bolts (4) and (5). Loosen bolt (6). 5. Remove governor housing (7) from the pump housing. 6. Remove spring (12), wave washer (11) and guide (10). Remove seat (8) and over fueling spring (9). 7. Pull shaft (13) up and remove it. Remove lever (14) from the housing. 8. Remove riser (follower) (17) from the shaft. Remove ring (15) and lever (16). 9. Remove cover (18) with tool (B). Tool (B) can cause damage to the cover. Always inspect the cover and install a new cover if needed.10. Install the timing pin to prevent the camshaft from turning. 11. Remove three bolts (19) that hold the flyweight assembly to the camshaft. Remove the flyweight assembly from the pump housing.12. Remove the timing pin.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install the timing pin to prevent the camshaft from turning. 3. Put flyweight assembly (1) in position on the camshaft.
Be sure pin (2) that holds the shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install the cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (3). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (4) on the dowel. Install ring (5). 8. Put riser (follower) (6) in position between the flyweights. Lift the flyweight up with a piece of wire and push the riser (follower) forward. 9. Put lever (10) in position. Lever (10) will be in the correct position when the lever end is in the groove of riser (follower) (6) and the ball end is engaged in sleeve shaft lever (9).
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to over speed.
10. Install O-ring (7). Install shaft (8) to hold lever (10) in place. 11. Install over fueling spring (12) and seat (11) on the shaft. 12. Install guide (13), (wave) washer (14) and spring (15) in the governor housing.13. Put the governor housing on the fuel injection pump housing and install the bolts.end by: a) install adapter housing and leversb) install fuel injection pump housing and governorc) make adjustment of fuel system setting (See Fuel System Setting in Testing and Adjusting)
1. Put the fuel injection pump housing on tool (A).2. Install the timing pin to prevent the camshaft from turning. 3. Put flyweight assembly (1) in position on the camshaft.
Be sure pin (2) that holds the shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install the cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (3). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (4) on the dowel. Install ring (5). 8. Put riser (follower) (6) in position between the flyweights. Lift the flyweight up with a piece of wire and push the riser (follower) forward. 9. Put lever (10) in position. Lever (10) will be in the correct position when the lever end is in the groove of riser (follower) (6) and the ball end is engaged in sleeve shaft lever (9).
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to over speed.
10. Install O-ring (7). Install shaft (8) to hold lever (10) in place. 11. Install over fueling spring (12) and seat (11) on the shaft. 12. Install guide (13), (wave) washer (14) and spring (15) in the governor housing.13. Put the governor housing on the fuel injection pump housing and install the bolts.end by: a) install adapter housing and leversb) install fuel injection pump housing and governorc) make adjustment of fuel system setting (See Fuel System Setting in Testing and Adjusting)