09180-03540 TIMER ASSY, AUTOMA Denso Cross


Rating:
15
Buy TIMER ASSY, AUTOMA 09180-03540 genuine, new aftermarket engine parts with delivery

Information timer assy, automa Denso

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09180-03540
TIMER ASSY, AUTOMA
SA1
001
[01]
HUB, TIMER
22516-1910A HINO
002
[02]
WEIGHT SUB-ASSY, T
22514-3390A HINO
003
[02]
CAM, TIMER
22545-1400A HINO
004
[02]
CAM, TIMER
22545-1410A HINO
005
[04]
WASHER, SNAP
ID6.4
22518-1110A HINO
006
[01]
FLANGE, TIMER DRIV
22513-2410A HINO
006-001
[01]
SEAL, OIL
22827-1680A HINO
007
[04]
SPRING, TIMER
22515-5280A HINO
008
[4C]
SPRING, TIMER SUB
L44.5
22515-5270A HINO
008
[4C]
SPRING, TIMER SUB
L46.4 9411-
008
[4C]
SPRING, TIMER SUB
L48.2 9411-
009
[02]
SUPPORT, TIMER SPR
22517-1590A HINO
010
[01]
COVER SUB-ASSY, TI
-0505
22501-1210A HINO
010
[01]
COVER SUB-ASSY, TI
0506-
010-001
[01]
SEAL, OIL
22827-1690A HINO
011
[04]
SEAT
22517-1570A HINO
012
[04]
SEAT
22517-1580A HINO
013
[02]
SCREW, TIMER HUB
M8
22865-1270A HINO
014
[01]
PLATE, TIMER DRIVI
T3.2
22513-2110A HINO
015
[02]
ROLLER, TIMER
22522-1040A HINO
016
[02]
WASHER, COPPER PLA
T1
22847-1300A HINO
017
[4C]
WASHER, PLATE, SK
T0.5
22885-5870A HINO
017
[4C]
WASHER, PLATE, SK
T0.6
22885-5880A HINO
017
[4C]
WASHER, PLATE, SK
T0.7
22885-5890A HINO
017
[4C]
WASHER, PLATE, SK
T0.8
017
[4C]
WASHER, PLATE, SK
T0.9
017
[4C]
WASHER, PLATE, SK
T1.0
22885-7830A HINO
017
[4C]
WASHER, PLATE, SK
T1.1
22885-7840A HINO
017
[4C]
WASHER, PLATE, SK
T1.2
22885-7850A HINO
017
[4C]
WASHER, PLATE, SK
T1.3
22885-7860A HINO
017
[4C]
WASHER, PLATE, SK
T1.4
22885-7890A HINO
017
[4C]
WASHER, PLATE, SK
T1.5
22885-7880A HINO
018
[01]
O-RING
ID110.8
22817-1930A HINO

Cross reference number



Part num
Firm num
Firm
Name
09180-03540 
 
TIMER ASSY, AUTOMA




Information:

Introduction
This Special Instruction contains the steps to remove a portion of a gusset inside the enclosure, near the DEF tank wire harness. The interference between the gusset and the wire harness may damage the wire harness. An improvement is already in production for machines after the listed range of Serial Numbers.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Caterpillar Channel 1 Videos
For supplemental information on this procedure, refer to the following video. The previous training has been replaced with the video below.Note: A CWS login is required to access Caterpillar Channel 1. Scan the QR code below with a QR enabled device or copy the link that follows.
Illustration 1 g06306276https://channel1.mediaspace.kaltura.com/media/Introduction+to+Visualization+Service+Procedures+%28VSP%29/1_92vjr92v
Safety Section
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
When removing a major component or attachment, ensure that it is properly blocked or secured before removing mounting hardware. An assembly that is disconnected without proper blocking may shift or fall, resulting in serious injury or death of personnel or machine damage.
Personal injury or death can result from improper maintenance procedures. To avoid injury or death, follow the procedures exactly as stated below.
Personal injury can result from improper handling of chemicals.Make sure you use all the necessary protective equipment required to do the job.Make sure that you read and understand all directions and hazards described on the labels and material safety data sheet of any chemical that is used.Observe all safety precautions recommended by the chemical manufacturer for handling, storage, and disposal of chemicals.
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information.
Before servicing/performing maintenance on the machine, electrical power must be physically disconnected; battery plugs must be disconnected from the batteries, or the trailing cable must be unplugged, and warning tags and padlocks shall be applied by a certified electrician. Certified electricians shall perform or direct any electrical work, including any energized testing, repair work in controllers, motors, or other approved compartments, and shall insure that all compartments are properly closed and inspected prior to re-energization. All applicable lock out and tag out procedures must be followed.
Do not operate the machine if any guards or covers are missing or inadequately secured. Personnel could be seriously injured or machine damage may occur.
Observe the safe working load limits of all lifting and blocking devices and keep a safe distance from suspended/blocked loads. Personnel may be seriously injured or killed by falling loads.
General Information
Graphic Color Description
Color-coding of targeted components, or sections of a part, is used to communicate a

Have questions with 09180-03540?





Group cross 09180-03540

Back to top