09180-02921 TIMER ASSY, AUTOMA Denso Cross


Rating:
66
Buy TIMER ASSY, AUTOMA 09180-02921 genuine, new aftermarket engine parts with delivery

Information timer assy, automa Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09180-02921
TIMER ASSY, AUTOMA
SA2
001
[01]
HUB, TIMER
002
[02]
WEIGHT SUB-ASSY, T
003
[02]
CAM, TIMER
-9103
003
[02]
CAM, TIMER
9103-
004
[02]
CAM, TIMER
-9103
004
[02]
CAM, TIMER
9103-
005
[04]
WASHER, SNAP
ID6.4
22518-1110A HINO
007
[01]
FLANGE, TIMER DRIV
-9406
007
[01]
FLANGE, TIMER DRIV
9407-
22513-2440A HINO
007-001
[01]
SEAL, OIL
ID34.6 -9406
22827-1490A HINO
007-001
[01]
SEAL, OIL
ID33.6 9407-
22827-1680A HINO
008
[4C]
SPRING, TIMER
K0.2
008
[4C]
SPRING, TIMER
K0.2
008
[4C]
SPRING, TIMER
K0.2
009
[4C]
SPRING, TIMER SUB
K0.55
009
[4C]
SPRING, TIMER SUB
K0.6
009
[4C]
SPRING, TIMER SUB
K0.65
010
[C]
WASHER, PLATE, SK
T0.5
22885-5870A HINO
010
[C]
WASHER, PLATE, SK
T0.6
22885-5880A HINO
010
[C]
WASHER, PLATE, SK
T0.7
22885-5890A HINO
010
[C]
WASHER, PLATE, SK
T0.8 9103-
010
[C]
WASHER, PLATE, SK
T0.9 9103-
011
[01]
O-RING
ID120
012
[02]
SUPPORT, TIMER SPR
22535-1140A HINO
013
[01]
COVER SUB-ASSY, TI
-9406
013
[01]
COVER SUB-ASSY, TI
9407--0505
22867-1830A HINO
013
[01]
COVER SUB-ASSY, TI
0506-
013-001
[01]
SEAL, OIL
ID37.3 -9406
22827-1500A HINO
013-001
[01]
SEAL, OIL
ID36.6 9407-
22827-1690A HINO
014
[01]
PLATE, TIMER DRIVI
22513-2270A HINO
015
[04]
SEAT
22517-1510A HINO
016
[02]
ROLLER, TIMER
22522-1060A HINO
017
[02]
WASHER, COPPER PLA
T1
22867-1500A HINO
018
[02]
SCREW, TIMER HUB
M8
22865-1270A HINO
019
[04]
SEAT

Include in ##:

09180-02921 as TIMER ASSY, AUTOMA

Cross reference number



Part num
Firm num
Firm
Name
09180-02921 
 
TIMER ASSY, AUTOMA




Information:

System Operation
A RTD measures the change in electrical resistance as a function of temperature. As the temperature increases the resistance increases. As the temperature decreases the resistance decreases. The resistance of a RTD varies linearly with temperature.The signal is routed from the engine mounted junction box to terminals in the MECP. The PLC routes the signal to a RTD module. The RTD module converts the signal into the parameter.The signal is used in order to trigger alarms and the signal is used in order to display the parameter.
Illustration 1 g00563639
Schematic of the RTD module
Illustration 2 g00563641
Schematic of the RTD
Illustration 3 g00562911
Schematic of the RTDFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the RTD.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the RTD from the wiring harness. This is done by removing the RTD connector head.
Measure the resistance on the sensor. Measure the resistance between the following terminals: Terminal 1 and Terminal 2.
Use table 1 in order to determine if the RTD is functioning normally.
Table 1
RTD
Temperature and Resistance    
Temperature    Ohms    Difference per °C    
0 °C (32 °F)     100.00     0.39    
10 °C (50.0 °F)     103.90     0.39    
20 °C (68 °F)     107.79     0.39    
30 °C (86 °F)     111.67     0.39    
40 °C (104 °F)     115.54     0.39    
50 °C (122 °F)     119.40     0.39    
60 °C (140 °F)     123.24     0.38    
70 °C (158 °F)     127.07     0.38    
80 °C (176 °F)     130.89     0.38    
90 °C (194 °F)     134.70     0.38    
100 °C (212 °F)     138.50     0.38    
110 °C (230 °F)     142.29     0.38    
120 °C (248 °F)     146.06     0.38    
130 °C (266 °F)     149.82     0.37    
140 °C (284 °F)     153.58     0.37    
150 °C (302 °F)     157.31     0.37    The results of the preceding procedure are in the following list:
The resistance

Have questions with 09180-02921?





Group cross 09180-02921

Back to top