09180-01540 TIMER ASSY, AUTOMA Denso Cross


Rating:
64
Buy TIMER ASSY, AUTOMA 09180-01540 genuine, new aftermarket engine parts with delivery

Information timer assy, automa Denso

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09180-01540
TIMER ASSY, AUTOMA
22610-68011 TOYOTA
001
[01]
HUB ASSY, TIMER
22616-68011 TOYOTA
002
[02]
WEIGHT SUB-ASSY, T
22614-68010 TOYOTA
003
[04]
SEAT
22629-68010 TOYOTA
004
[02]
SPRING, TIMER
22615-68012 TOYOTA
005
[02]
SPRING, TIMER SUB
22628-68011 TOYOTA
006
[01]
GEAR, DRIVE
22626-68010 TOYOTA
007
[01]
RING, SHAFT SNAP
ID28
90096-90021 TOYOTA
008
[01]
WASHER, PLATE, SK
T1.0
90099-01471 TOYOTA
009
[1C]
WASHER, PLATE, SK
T0.2
90099-01470 TOYOTA
009
[1C]
WASHER, PLATE, SK
T0.1
90099-01472 TOYOTA
010
[2C]
WASHER, PLATE, SK
T0.3
90099-01194 TOYOTA
010
[2C]
WASHER, PLATE, SK
T0.1
90099-02315 TOYOTA
010
[2C]
WASHER, PLATE, SK
T0.2
90099-01369 TOYOTA
010
[2C]
WASHER, PLATE, SK
T0.5
90099-01381 TOYOTA
010
[2C]
WASHER, PLATE, SK
T1.0
90099-01382 TOYOTA

Cross reference number



Part num
Firm num
Firm
Name
09180-01540 
22610-6801 
TIMER ASSY, AUTOMA
0918001540 
22610-68011 
TOYOTA
TIMER ASSY, AUTOMA
0918001540 
26106-8020 
TOYOTA
TIMER ASSY, AUTOMA




Information:

Start By:a. remove timing gear cover
Do not disconnect the air line from the air compressor governor until the air pressure is zero.
1. Loosen the bleed valves, and release the air pressure in the air tank. 2. Disconnect the lines from air compressor (1), and remove the air compressor. 3. Remove sleeve (2) from air compressor drive gear (3). 4. Remove the nut and washer that holds the air compressor drive gear to the air compressor. Use tooling (A) to remove air compressor drive gear (3) from the air compressor. 5. Remove nuts (4) and plate (5). Remove gear assembly (6) from the shaft. 6. If damaged, remove bearing (7) from gear assembly (6) with tooling (B) and a press. 7. Remove three nuts (8) and the washers from the adapter assembly studs.
Typical Example8. Remove adapter assembly (9) from the timing gear plate. 9. Remove shaft (10), O-ring seal (11) and sleeve (12) from the adapter assembly.Install Air Compressor And Accessory Drive
1. Install sleeve (12) into the adapter assembly.2. Install shaft (10) and O-ring seal (11) on the adapter assembly. 3. Put adapter assembly (9) in position on the timing gear plate. Fasten it with the three nuts and washers. 4. Install the bearing in gear assembly (6) with tooling (A) and a press. Install the bearing until it is 1.5 0.5 mm (.06 .02 in.) below the surface of the gear as shown. 5. Put gear assembly (6) in position on the shaft.6. Put plate (5) in position, and install three nuts (4) to hold it. 7. Put air compressor drive gear (3) in position on the air compressor shaft, and install the washer and nut (13). Tighten the nut to a torque of 200 25 N m (150 18 lb.in.). Tap the gear with a hammer and tighten nut (13) again to a torque of 200 25 N m (150 18 lb.ft.). 8. Install sleeve (2) on gear (3). 9. Put a gasket in position on air compressor (1) and install the air compressor on the timing cover plate.End By:a. install timing gear cover

Have questions with 09180-01540?





Group cross 09180-01540

Back to top