09180-01150 TIMER ASSY, AUTOMA Denso Cross


Rating:
8
Buy TIMER ASSY, AUTOMA 09180-01150 genuine, new aftermarket engine parts with delivery

Information timer assy, automa Denso

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa
Timer assy, automa

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09180-01150
TIMER ASSY, AUTOMA
SA/2SP
000
[01]
09180-01150
TIMER ASSY, AUTOMA
SA/2SP
22610-77050 TOYOTA
001
[01]
HUB ASSY, TIMER
001
[01]
HUB ASSY, TIMER
002
[02]
SPRING, TIMER
002
[02]
SPRING, TIMER
22615-77050 TOYOTA
003
[02]
SPRING, TIMER SUB
003
[02]
SPRING, TIMER SUB
22628-77050 TOYOTA
004
[01]
O-RING
ID115.0
004
[01]
O-RING
ID115.0
90099-14001 TOYOTA
005
[02]
WEIGHT, TIMER
005
[02]
WEIGHT, TIMER
22614-77040 TOYOTA
006
[01]
FLANGE, TIMER DRIV
006
[01]
FLANGE, TIMER DRIV
22613-77050 TOYOTA
007
[01]
SEAL, OIL
D95,T5
007
[01]
SEAL, OIL
D95,T5
90099-15005 TOYOTA
008
[01]
SEAL, OIL
D38,T7
008
[01]
SEAL, OIL
D38,T7
90099-15004 TOYOTA
009
[01]
COVER, TIMER
009
[01]
COVER, TIMER
010
[02]
WASHER, COPPER PLA
T1
90201-08106 TOYOTA
010
[02]
WASHER, COPPER PLA
T1
90201-08106 TOYOTA
011
[02]
SCREW, TIMER HUB
M8
011
[02]
SCREW, TIMER HUB
M8
22617-77020 TOYOTA
012
[2C]
WASHER, PLATE, SK
T0.5
012
[2C]
WASHER, PLATE, SK
T0.5
90099-01453 TOYOTA
012
[2C]
WASHER, PLATE, SK
T0.2
012
[2C]
WASHER, PLATE, SK
T0.2
90099-01454 TOYOTA
014
[04]
SEAT
014
[04]
SEAT
22629-77130 TOYOTA
015
[3C]
WASHER, PLATE, SK
T0.5
015
[3C]
WASHER, PLATE, SK
T0.5
22621-77020 TOYOTA
015
[3C]
WASHER, PLATE, SK
T1.0
015
[3C]
WASHER, PLATE, SK
T1.0
22622-77020 TOYOTA
015
[3C]
WASHER, PLATE, SK
T0.1
015
[3C]
WASHER, PLATE, SK
T0.1
22623-77020 TOYOTA
015
[3C]
WASHER, PLATE, SK
T0.2
015
[3C]
WASHER, PLATE, SK
T0.2
22624-77020 TOYOTA
015
[3C]
WASHER, PLATE, SK
T1.6
015
[3C]
WASHER, PLATE, SK
T1.6
22625-77020 TOYOTA
015
[3C]
WASHER, PLATE, SK
T2.0
015
[3C]
WASHER, PLATE, SK
T2.0
90099-01442 TOYOTA

Cross reference number



Part num
Firm num
Firm
Name
09180-01150 
 
TIMER ASSY, AUTOMA
0918001150 
22610-77050 
TOYOTA
TIMER ASSY, AUTOMA




Information:

1. Remove bolts (1) that hold plate (2), and remove the plate. 2. Remove bolts (3) and (4) that hold the cylinder head assembly to the cylinder block.3. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
4. Remove the gasket, seals (5) and O-ring seals (6) from the spacer plate. The following steps are for installation of the cylinder head. Be sure a new gasket has been installed between the spacer plate and the cylinder block. See the topic, Remove And Install Spacer Plate.5. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (5) and two O-ring seals (6).6. Fasten a hoist, and put the cylinder head assembly in position on the cylinder block. 7. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See the topic, Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts (5) to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).8. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).9. Install the valve cover bases and the inner fuel lines. See the topic, Install Rocker Shaft Assemblies And Push Rods.10. Install the valve covers. See Install Valve Covers.11. Install plate (2).End By:a. install aftercooler housingb. install exhaust manifoldc. install fuel injection linesd. install water temperature regulator

Have questions with 09180-01150?





Group cross 09180-01150

Back to top