Rating:
Information seat, spring Denso
Include in ##:
Number on scheme 001-006
09350-06010
as SEAT, SPRING
Cross reference number
Part num
Firm num
Firm
Name
09312-81010
SEAT, SPRING
0931281010
ME743488
MITSUBISHI
SEAT, SPRING
Information:
Introduction
This Special Instruction covers the procedure to install a Wall Flow Diesel Particulate Filter (WFDPF) on the above listed machines, equipped with Ventilation Reduction Package, and the correct low sulphur fuel and low ash oil.This supplemental product support literature should be used with the appropriate Service Manual and the appropriate Parts Manual that is available for this standard machine.Read the entire Special Instruction. Understand the information before you perform any procedures. Understand the information before you order any parts.Note: This procedure cannot be used in Canadian provinces that require "CANMET"certification. This procedure will invalidate the existing "CANMET" approval for an engine.Safety Section
Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive.Ensure that all personnel are safe when using a tool, procedure, work method, or operating technique not recommended by Caterpillar. Ensure that the product will not be damaged or the product made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Personal injury or death can result from machine articulation or movement. Machine frames can move and a person can be crushed. Connect the steering frame lock between the front and rear frames before working on the machine.Before operating the machine, place the steering frame lock in the stored position.Failure to place the steering frame lock into the stored position before operating can result in loss of steering.
The muffler, catalytic converter/muffler, and diesel particulate filter will become extremely hot during engine operation. A hot muffler, catalytic converter/muffler and diesel particulate filter can cause serious burns. Allow adequate cooling time before working on or near the muffler, catalytic converter/muffler and diesel particulate filter.
Diesel engine exhaust contains products of combustion which may cause personal injury.Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Reference: Disassembly and Assembly, RENR8556, "R2900G Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR7184, "R2900G Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR1483, "R3000H Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR7202, "R3000H Load Haul Dump Machine Systems"Reference: Disassembly & Assembly Supplement, RENR8559, "R2900G Load Haul Dump, C15 Engine".Reference: Disassembly & Assembly Supplement, UENR1471, "R3000H Load Haul Dump, C15 Engine".Required Parts
Table 1
Qty Part Number Part Description
1 147-0385 Clip
1 228-7100 O-Ring Seal
1
This Special Instruction covers the procedure to install a Wall Flow Diesel Particulate Filter (WFDPF) on the above listed machines, equipped with Ventilation Reduction Package, and the correct low sulphur fuel and low ash oil.This supplemental product support literature should be used with the appropriate Service Manual and the appropriate Parts Manual that is available for this standard machine.Read the entire Special Instruction. Understand the information before you perform any procedures. Understand the information before you order any parts.Note: This procedure cannot be used in Canadian provinces that require "CANMET"certification. This procedure will invalidate the existing "CANMET" approval for an engine.Safety Section
Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive.Ensure that all personnel are safe when using a tool, procedure, work method, or operating technique not recommended by Caterpillar. Ensure that the product will not be damaged or the product made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Personal injury or death can result from machine articulation or movement. Machine frames can move and a person can be crushed. Connect the steering frame lock between the front and rear frames before working on the machine.Before operating the machine, place the steering frame lock in the stored position.Failure to place the steering frame lock into the stored position before operating can result in loss of steering.
The muffler, catalytic converter/muffler, and diesel particulate filter will become extremely hot during engine operation. A hot muffler, catalytic converter/muffler and diesel particulate filter can cause serious burns. Allow adequate cooling time before working on or near the muffler, catalytic converter/muffler and diesel particulate filter.
Diesel engine exhaust contains products of combustion which may cause personal injury.Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Reference: Disassembly and Assembly, RENR8556, "R2900G Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR7184, "R2900G Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR1483, "R3000H Load Haul Dump Machine Systems"Reference: Disassembly and Assembly, UENR7202, "R3000H Load Haul Dump Machine Systems"Reference: Disassembly & Assembly Supplement, RENR8559, "R2900G Load Haul Dump, C15 Engine".Reference: Disassembly & Assembly Supplement, UENR1471, "R3000H Load Haul Dump, C15 Engine".Required Parts
Table 1
Qty Part Number Part Description
1 147-0385 Clip
1 228-7100 O-Ring Seal
1