Rating:
Information seat, spring Denso
Include in ##:
Number on scheme 001-006
09350-06010
as SEAT, SPRING
Cross reference number
Part num
Firm num
Firm
Name
09312-80120
SEAT, SPRING
0931280120
ME736600
MITSUBISHI
SEAT, SPRING
Information:
Introduction
Do not perform any procedure in the Special Instruction until you read and understand the information that is contained in this document. Caterpillar recommends that no wires thinner than 18 AWG wire are used in the installation of this kit. Caterpillar recommends that some form of circuit protection (that is, circuit breakers) be used to protect the Electronic Control Module (ECM) in cases where there is a direct electrical connection to the battery. Caterpillar recommends that a keyswitch is used to control the power delivery to terminal J1-70 of the ECM to control when the ECM is ON and OFF.Battery power (+) must be supplied to terminals J1-48, 52, 53, and 55 of the ECM and to certain parts where appropriate. A ground/return (-) must be supplied to terminals J1-61, 63, 65, and 69 of the ECM and to certain parts where appropriate. In order to turn on the ECM, power must also be supplied to terminal J1-70 of the ECM. The 160-7689 Connector Plug As connects to the J1 terminal of the ECM.Required Parts
The 356-3348 Kit - Regeneration Switch contains the following parts.
Table 1
Required Parts
Qty Part Number Description
1 205-5471 Connector
2 245-7434 Connecting Plug Kit
1 242-3282 LED Lamp As
1 284-3623 Rocker Switch
1 327-6999 Rocker Switch
1 332-1064 Illuminated Plug
1 102-8802 Receptacle Kit
1 372-6047 Indicator
4 112-9611 Blade Terminal
1 155-2274 Connecting Plug Kit Installing the Red LED Lamp (Regeneration Disable Lamp)
Illustration 1 g02402796
242-3282 Led Lamp As Use 155-2269 Connector Plug As as a mating connector. 155-2269 Connector Plug As is not included in the kit. Also, 102-8802 Receptacle Kit contains 3E-3364 Receptacle and 3E-3365 Receptacle Lock Wedge .
Insert the red (power) wire from the 242-3282 LED Lamp As into terminal 1 of 3E-3364 Receptacle .
Insert the black (ground) wire from the LED lamp into terminal 2 of the receptacle.
Insert 3E-3365 Receptacle Lock Wedge is the receptacle.
Connect terminal 1 of the receptacle to terminal 13 of 160-7689 Connector Plug As .
Connect terminal 2 of the receptacle to the ground/return (-).Installing the Illuminated Plug (Regeneration Lamp)
Illustration 2 g02402326
332-1064 Illuminated Plug The terminal designations can be found on the sides of 332-1064 Illuminated Plug and 205-5471 Connector .
Connect terminal 1A of the connector to the battery power (+).
Connect terminal 2A of the connector to the battery power (+).
Connect terminal 1B of the connector to terminal 30 of the plug.
Connect terminal 2B of the connector to terminal 31 of the plug.
Crimp the 112-9611 Blade Terminal onto the wires necessary to create the connections described in the previous steps.
Insert the blade terminals into the appropriate terminal locations of the connector.
Connect the plug to the connector. The plug and the connector are mating connectors.Installing
Do not perform any procedure in the Special Instruction until you read and understand the information that is contained in this document. Caterpillar recommends that no wires thinner than 18 AWG wire are used in the installation of this kit. Caterpillar recommends that some form of circuit protection (that is, circuit breakers) be used to protect the Electronic Control Module (ECM) in cases where there is a direct electrical connection to the battery. Caterpillar recommends that a keyswitch is used to control the power delivery to terminal J1-70 of the ECM to control when the ECM is ON and OFF.Battery power (+) must be supplied to terminals J1-48, 52, 53, and 55 of the ECM and to certain parts where appropriate. A ground/return (-) must be supplied to terminals J1-61, 63, 65, and 69 of the ECM and to certain parts where appropriate. In order to turn on the ECM, power must also be supplied to terminal J1-70 of the ECM. The 160-7689 Connector Plug As connects to the J1 terminal of the ECM.Required Parts
The 356-3348 Kit - Regeneration Switch contains the following parts.
Table 1
Required Parts
Qty Part Number Description
1 205-5471 Connector
2 245-7434 Connecting Plug Kit
1 242-3282 LED Lamp As
1 284-3623 Rocker Switch
1 327-6999 Rocker Switch
1 332-1064 Illuminated Plug
1 102-8802 Receptacle Kit
1 372-6047 Indicator
4 112-9611 Blade Terminal
1 155-2274 Connecting Plug Kit Installing the Red LED Lamp (Regeneration Disable Lamp)
Illustration 1 g02402796
242-3282 Led Lamp As Use 155-2269 Connector Plug As as a mating connector. 155-2269 Connector Plug As is not included in the kit. Also, 102-8802 Receptacle Kit contains 3E-3364 Receptacle and 3E-3365 Receptacle Lock Wedge .
Insert the red (power) wire from the 242-3282 LED Lamp As into terminal 1 of 3E-3364 Receptacle .
Insert the black (ground) wire from the LED lamp into terminal 2 of the receptacle.
Insert 3E-3365 Receptacle Lock Wedge is the receptacle.
Connect terminal 1 of the receptacle to terminal 13 of 160-7689 Connector Plug As .
Connect terminal 2 of the receptacle to the ground/return (-).Installing the Illuminated Plug (Regeneration Lamp)
Illustration 2 g02402326
332-1064 Illuminated Plug The terminal designations can be found on the sides of 332-1064 Illuminated Plug and 205-5471 Connector .
Connect terminal 1A of the connector to the battery power (+).
Connect terminal 2A of the connector to the battery power (+).
Connect terminal 1B of the connector to terminal 30 of the plug.
Connect terminal 2B of the connector to terminal 31 of the plug.
Crimp the 112-9611 Blade Terminal onto the wires necessary to create the connections described in the previous steps.
Insert the blade terminals into the appropriate terminal locations of the connector.
Connect the plug to the connector. The plug and the connector are mating connectors.Installing