Rating:
Information pump assy, supply Denso
Product
Fuel Injection Pump
Vehicle engine
NAVARA YD2K2
Engine
YD2K2
Serial start-end
0610-
Info
For Europe etc. HU294000-0530, Nissan P/N 16700-EC00A
Injector Nozzle
NISSAN MOTOR
PUMP ASSY, SUPPLY
IA
- DMHU PRODUCTION HU294000-053#.
- *3:SHAPE CHANGE OF THE INLET PIPE. IF THE FUEL HOSE
- (CAR PART)IS REPLACED AT THE SAME TIME, THE NEW ONE CAN
- BE USED INSTEAD OF THE OLD ONE.
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
HU294-00005
16700EC01D
NISSAN MOTOR
PUMP ASSY, SUPPLY
HU2940000530
16700EC01D
NISSAN MOTOR
PUMP ASSY, SUPPLY
Information:
Engine Design
CYLINDER AND VALVE LOCATIONBore ... 5.40 in.(137.2 mm)Stroke ... 6.50 in.(165.1 mm)Number and Arrangement of Cylinders ... 6, In LineFiring Order (Injection Sequence) ... 1, 5, 3, 6, 2, 4No. 1 Cylinder Location ... FrontRotation of Crankshaft (when seen from flywheel end) ... counterclockwiseRotation of Fuel Pump Camshaft (when seen from pump drive end) ... counterclockwiseFuel System
FUEL SYSTEM
1. Injection valve. 2. Anti-siphon block. 3. Injection pump housing. 4. Priming pump. 5. Plug. 6. Secondary filter. 7. Fuel line. 8. Return line to tank. 9. Fuel tank. 10. Primary filter. 11. Transfer pump.This engine has a pressure type fuel system. There is a single injection pump and injection valve (1) for each cylinder. The injection pumps are in the pump housing (3) on the left side of the engine. The injection valves (1) are in the precombustion chambers or adapters under the valve cover.The transfer pump (11) pulls fuel from the fuel tank (9) through the primary filter (10) and sends it through the base of priming pump (4) and the secondary filter (6), through the anti-siphon block (2) and to the manifold of the injection pump housing. When priming pump (4) is not used, the position of fuel line (7) and plug (5) are reversed. The fuel in the manifold of the injection pump housing goes to the injection pumps. The injection pumps are in time with the engine and send fuel to the injection valves under high pressure.Some of the fuel in the manifold is constantly sent back through the anti-siphon block (2) and through the return line (8) to the fuel tank to remove air from the system. Orifices in the anti-siphon block control the amount of fuel that goes back to the fuel tank.The priming pump (4) is used to remove air from the fuel filter, fuel lines and components.The transfer pump has a bypass valve and a check valve. The bypass valve (lower side) gives control to the pressure of the fuel. The extra fuel goes to the inlet of the pump.Fuel Injection Pump Operation
Injection pump plungers (4) and lifters (8) are lifted by cams on camshaft (9) and always make a full stroke. The force of springs (5) hold the lifters (8) against the cams of the camshaft.Fuel from fuel manifold (1) goes through inlet passage (2) in the barrel and then into the chamber above plunger (4). During injection, the camshaft cam moves plunger (4) up in the barrel. This movement will close inlet passage (2) and push the fuel out through the fuel lines to the injection valves.The amount of fuel sent to the injection valves is controlled by turning plunger (4) in the barrel. When the governor moves fuel rack (7), the fuel rack moves gear (6) that is fastened to the bottom of plunger (4).
CROSS SECTION OF THE HOUSING FOR THE FUEL INJECTION PUMPS
1. Fuel manifold. 2. Inlet passage in pump barrel. 3. Check valve. 4. Pump plunger. 5. Spring. 6. Gear. 7. Fuel rack. 8. Lifter. 9.
CYLINDER AND VALVE LOCATIONBore ... 5.40 in.(137.2 mm)Stroke ... 6.50 in.(165.1 mm)Number and Arrangement of Cylinders ... 6, In LineFiring Order (Injection Sequence) ... 1, 5, 3, 6, 2, 4No. 1 Cylinder Location ... FrontRotation of Crankshaft (when seen from flywheel end) ... counterclockwiseRotation of Fuel Pump Camshaft (when seen from pump drive end) ... counterclockwiseFuel System
FUEL SYSTEM
1. Injection valve. 2. Anti-siphon block. 3. Injection pump housing. 4. Priming pump. 5. Plug. 6. Secondary filter. 7. Fuel line. 8. Return line to tank. 9. Fuel tank. 10. Primary filter. 11. Transfer pump.This engine has a pressure type fuel system. There is a single injection pump and injection valve (1) for each cylinder. The injection pumps are in the pump housing (3) on the left side of the engine. The injection valves (1) are in the precombustion chambers or adapters under the valve cover.The transfer pump (11) pulls fuel from the fuel tank (9) through the primary filter (10) and sends it through the base of priming pump (4) and the secondary filter (6), through the anti-siphon block (2) and to the manifold of the injection pump housing. When priming pump (4) is not used, the position of fuel line (7) and plug (5) are reversed. The fuel in the manifold of the injection pump housing goes to the injection pumps. The injection pumps are in time with the engine and send fuel to the injection valves under high pressure.Some of the fuel in the manifold is constantly sent back through the anti-siphon block (2) and through the return line (8) to the fuel tank to remove air from the system. Orifices in the anti-siphon block control the amount of fuel that goes back to the fuel tank.The priming pump (4) is used to remove air from the fuel filter, fuel lines and components.The transfer pump has a bypass valve and a check valve. The bypass valve (lower side) gives control to the pressure of the fuel. The extra fuel goes to the inlet of the pump.Fuel Injection Pump Operation
Injection pump plungers (4) and lifters (8) are lifted by cams on camshaft (9) and always make a full stroke. The force of springs (5) hold the lifters (8) against the cams of the camshaft.Fuel from fuel manifold (1) goes through inlet passage (2) in the barrel and then into the chamber above plunger (4). During injection, the camshaft cam moves plunger (4) up in the barrel. This movement will close inlet passage (2) and push the fuel out through the fuel lines to the injection valves.The amount of fuel sent to the injection valves is controlled by turning plunger (4) in the barrel. When the governor moves fuel rack (7), the fuel rack moves gear (6) that is fastened to the bottom of plunger (4).
CROSS SECTION OF THE HOUSING FOR THE FUEL INJECTION PUMPS
1. Fuel manifold. 2. Inlet passage in pump barrel. 3. Check valve. 4. Pump plunger. 5. Spring. 6. Gear. 7. Fuel rack. 8. Lifter. 9.