Rating:
Information pump assy, supply Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
6H04 HP4 Diesel Fuel Injection Pump 294050-0020 294050-0029
LCQBXGPU Long lifespan, stable and durable || Enhance power and solve oil leakage || Smooth start-up and improved fuel consumption || Excellent raw materials and advanced technology || 6H04 HP4 Diesel Fuel Injection Pump 294050-0020 294050-0029
LCQBXGPU Long lifespan, stable and durable || Enhance power and solve oil leakage || Smooth start-up and improved fuel consumption || Excellent raw materials and advanced technology || 6H04 HP4 Diesel Fuel Injection Pump 294050-0020 294050-0029
$1,399.00
11 Jul 2024
CN: yahegochengeg
shsiyayh Fuel Injection Pump HP4 294050-0027 294050-0029 for ISUZU N SERIES 6H04 Engine
shsiyayh Part Name:Fuel Injection Pump || Part Number:294050-0027 294050-0029 2940500027 2940500029 || APPlication: Compatible with ISUZU N SERIES 6H04 Engine || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
shsiyayh Part Name:Fuel Injection Pump || Part Number:294050-0027 294050-0029 2940500027 2940500029 || APPlication: Compatible with ISUZU N SERIES 6H04 Engine || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
29405-00029
8-97602049
PUMP ASSY, SUPPLY
Information:
Be very careful never to mix metric with U.S. customary (standard) fasteners. Mismatched or incorrect fasteners will cause engine damage or malfunction and may even result in personal injury.Original fasteners removed from the engine should be saved for reassembly whenever possible. If new fasteners are needed, they must be of the same size and grade as the ones that are being replaced.The material strength identification is usually shown on the bolt head by numbers (8.8, 10.9, etc.). The following chart gives general torques for bolts and nuts with Metric Threads of SAE Grade 8.8 or better quality.
Metric hardware must be replaced with metric hardware. Check parts manual for proper replacement.Torque for Standard Hose Clamps-Worm Drive Band Type
The following chart gives the torques for initial installation of hose clamps on new hose and for reassembly or tightening of hose clamps on existing hose.
Torque for Constant Torque Hose Clamps
A constant torque hose clamp can be used in place of any standard hose clamp. Make sure the constant torque hose clamp is the same size as the standard clamp. Due to extreme temperature changes, the hose will heat set. Heat setting causes hose clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures caused by hose clamps loosening. The new, constant torque hose clamp will help prevent these failures.Each installation/application can be different depending on the type of hose, fitting material and anticipated expansion or contraction of the hose and fittings. A torque wrench should be used for proper installation of the new, constant torque hose clamps. Constant torque hose clamps should be installed as follows:* To allow for maximum expansion, install clamps at 5.7 N m (50 lb in).* To allow for equal expansion and contraction, install clamps at 10.2 N m (90 lb in).* To allow for maximum contraction, install clamps at 14.1 N m (125 lb in).