29400-02490 TOYOTA PUMP ASSY, SUPPLY Calibration Data


Rating:
17
Buy PUMP ASSY, SUPPLY 29400-02490 TOYOTA genuine, new aftermarket engine parts with delivery

Information pump assy, supply Denso

Product
Fuel Injection Pump
Vehicle engine
IMV 1KD-FTV
Engine
1KD-FTV
Serial start-end
1502-
Info
Injector Nozzle
TOYOTA PUMP ASSY, SUPPLY AA
  • * SIAM DENSO PRODUCTION SM294000-249#

Components :

00.001
PUMP ASSY, SUPPLY
01.002
OVERHAUL KIT, SUPP
O/H KIT*

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
29400-02490
PUMP ASSY, SUPPLY
22100-0L102 TOYOTA
001
[01]
HOUSING SUB-ASSY,
002
[02]
WASHER, CAMSHAFT
003
[01]
CAMSHAFT, SUPPLY P
004
[01]
KEY, WOODRUFF
005
[01]
RING SUB-ASSY, CAM
006
[01]
COVER SUB-ASSY, BE
006-001
[01]
SEAL, OIL
D30
007
[06]
BOLT, SOCKET
M6,L16
008
[01]
O-RING, SUPPLY PUM
ID53.7
009
[02]
O-RING, SUPPLY PUM
ID51.2
010
[01]
PLATE, FEED PUMP,
011
[01]
COVER, FEED PUMP
012
[01]
KEY, FEED PUMP
013
[01]
ROTOR SET, FEED PU
014
[05]
BOLT, SOCKET
M6,L20
015
[01]
ELEMENT KIT, SUPPL
016
[01]
ELEMENT KIT, SUPPL
017
[02]
SPRING, PLUNGER
L32.9
018
[02]
O-RING, SUPPLY PUM
ID5.0
019
[02]
O-RING, SUPPLY PUM
ID28.5
020
[06]
BOLT, SOCKET
M8,L30.5
021
[02]
VALVE SUB-ASSY, SU
NO SUPPLY
022
[02]
O-RING, SUPPLY PUM
023
[02]
PLUG, CYLINDER
033
[01]
VALVE ASSY, SUCTIO
SCV
033-001
[01]
O-RING, VALVE
ID13.0
034
[01]
O-RING, SOLENOID
ID19.8
035
[01]
VALVE SUB-ASSY, RE
035-001
[01]
O-RING, SUPPLY PUM
ID 7.5
035-002
[01]
O-RING, SUPPLY PUM
ID10.5
036
[01]
PIPE, SUPPLY PUMP
037
[02]
PIN, STOPPER
L10.5
038
[01]
PLUG, FILTER
039
[01]
GASKET, PLUG
ID14.3
040
[01]
FILTER SUB-ASSY
041
[01]
O-RING, SUPPLY PUM
ID 6.5
043
[01]
SCREW, HOLLOW
044
[01]
COLLAR, FUEL OUTLE
M10,L14
052
[01]
CAP, VALVE HOLDER
M12
053
[01]
COVER, RUBBER
FOR D8
054
[01]
COVER, RUBBER
FOR D6.35
101
[01]
OVERHAUL KIT, SUPP
FILTER KIT
200
[01]
OVERHAUL KIT, SUPP
O/H KIT
201
[02]
OVERHAUL KIT, SUPP
SUCTION
202
[01]
ELEMENT KIT, SUPPL
203
[01]
ELEMENT KIT, SUPPL
204
[02]
HOLDER, DELIVERY V

Include in ##:

29400-02490 as PUMP ASSY, SUPPLY

Cross reference number



Part num
Firm num
Firm
Name
29400-02490 
22100-0L10 
TOYOTA
PUMP ASSY, SUPPLY
2940002490 
22100-0L102 
TOYOTA
PUMP ASSY, SUPPLY

Test Calibration Data:

02EN249000




Information:

Start By:a. remove automatic timing advance unit
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
Before any timing gears are removed, make sure "C" on the crankshaft gear is in alignment with "C" mark on the camshaft gear. 1. Remove bolts, plate (1) and fuel pump idler gear (2). 2. Remove bearing from idler gear (2) with tool (A). 3. Remove four bolts (3) and camshaft gear (4). 4. Remove bolts that are used to fasten shield (5) in position between the fuel pump and the exhaust manifold. Slide shield back from the timing cover plate.5. Remove the three nuts (6). 6. Remove six bolts (7). Remove the timing gear plate and the gasket. The following steps are to install the timing gears and plate.7. Clean the old gasket from the contact surfaces of the timing gear plate and cylinder block. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block.8. Be sure the O-ring seals are in position on the end of the fuel injection pump housing. Put the timing gear plate in position on the cylinder block and install the six bolts (7). Install nuts (6).
After the timing gear plate is installed, be sure the rack is free to move in the fuel injection pump housing. The O-ring seal on the drive end of the fuel injection pump housing can hold the rack and prevent free rack movement. Rack movement can be seen through hole in the timing gear plate just above where the fuel pump gear is mounted. If the rack does not move freely, remove the timing gear plate and check the O-ring seal on the drive end of the fuel injection pump housing. If the rack does not move freely, the engine can over speed and be damaged. Serious personal injury can be the result.
9. Install camshaft gear (4) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear as shown in the illustration in the Specification section of this manual. Tighten the volts to a torque of 55 7 N m (41 5 lb ft).10. Use tooling (A) to install the bearing in idler gear (2). The end of the bearing must be 1.52 .025 mm (.060 .010 in) below the face of the gear hub.11. Be sure the oil hole in the shaft for gear (2) is open. Install idler gear (2). Put the plate on position with the finished side toward gear (2) and install the bolts.12. Install shield (5) and the four bolts.End By:a. install automatic timing advance unit

Have questions with 29400-02490?





Group cross 29400-02490 TOYOTA

Back to top