Rating:
Information pump assy, supply Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
294000-0950 294000-0951 294000-0952 High Pressure Fuel Pump Assy 6C1Q-9B395-BD/BE/BF 6C1Q 9B395 BF Compatible With Transit V348 2.4L
AJZWGTHI The core function of a high-pressure fuel pump is to compress and convert the fuel in the bottom pressure fuel pipe into a high-pressure fuel pump || The high-pressure fuel pump increases the fuel pressure to reach a high-pressure state, achieving fuel injection and providing effective power source for the engine || High pressure fuel pump improves fuel atomization results, protects engine normal operation, and provides sufficient power || High pressure fuel pump improves emissions by controlling fuel injection and pressure, reducing fuel waste and carbon emissions, and enhancing the environmental performance of your car || 294000-0950 294000-0951 294000-0952 High Pressure Fuel Pump Assy 6C1Q-9B395-BD/BE/BF 6C1Q 9B395 BF Compatible With Transit V348 2.4L
AJZWGTHI The core function of a high-pressure fuel pump is to compress and convert the fuel in the bottom pressure fuel pipe into a high-pressure fuel pump || The high-pressure fuel pump increases the fuel pressure to reach a high-pressure state, achieving fuel injection and providing effective power source for the engine || High pressure fuel pump improves fuel atomization results, protects engine normal operation, and provides sufficient power || High pressure fuel pump improves emissions by controlling fuel injection and pressure, reducing fuel waste and carbon emissions, and enhancing the environmental performance of your car || 294000-0950 294000-0951 294000-0952 High Pressure Fuel Pump Assy 6C1Q-9B395-BD/BE/BF 6C1Q 9B395 BF Compatible With Transit V348 2.4L
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
Cross reference number
Part num
Firm num
Firm
Name
29400-00952
PUMP ASSY, SUPPLY
Information:
Start Bya. remove flywheel
Do not damage the flange on the crankshaft when the crankshaft rear seal is removed. Use of any other tool, other than Tool (A), to remove the crankshaft rear seal, can result in damage to the crankshaft.
1. Carefully make three evenly spaced holes in the crankshaft rear seal with a hammer and sharp punch. Use Tool (A) to remove crankshaft rear seal (1). Do not damage the flange of the crankshaft during seal removal. The following steps are for the installation of the crankshaft rear seal.2. Be sure the flange of the crankshaft is thoroughly clean prior to seal installation. 3. Fasten the 1U7595 Locator Assembly [part of Tool (B)] to the rear of the crankshaft as shown.4. Leaving the seal shipping sleeve in position on the new crankshaft rear seal, position the new seal over the locator assembly. The 1U7597 Sleeve Ring [part of Tool (B)] is not used in this in the seal installation.5. Install the 1U7594 Installer [part of Tool (B)] on the locator assembly. Tighten the nut assembly of Tool (B) to push the crankshaft rear seal into position on the flange of the crankshaft. Remove Tool (B) and the shipping sleeve. The distance between the front face of the crankshaft rear seal and the rear face of the cylinder block must be 15.4 0.5 mm (.61 .02 in) after seal installation. See the topic "Crankshaft Seals" in the 3114 & 3116 Diesel Truck Engines Specifications module, Form No. SENR6436 for further details.End By:a. install flywheel
Do not damage the flange on the crankshaft when the crankshaft rear seal is removed. Use of any other tool, other than Tool (A), to remove the crankshaft rear seal, can result in damage to the crankshaft.
1. Carefully make three evenly spaced holes in the crankshaft rear seal with a hammer and sharp punch. Use Tool (A) to remove crankshaft rear seal (1). Do not damage the flange of the crankshaft during seal removal. The following steps are for the installation of the crankshaft rear seal.2. Be sure the flange of the crankshaft is thoroughly clean prior to seal installation. 3. Fasten the 1U7595 Locator Assembly [part of Tool (B)] to the rear of the crankshaft as shown.4. Leaving the seal shipping sleeve in position on the new crankshaft rear seal, position the new seal over the locator assembly. The 1U7597 Sleeve Ring [part of Tool (B)] is not used in this in the seal installation.5. Install the 1U7594 Installer [part of Tool (B)] on the locator assembly. Tighten the nut assembly of Tool (B) to push the crankshaft rear seal into position on the flange of the crankshaft. Remove Tool (B) and the shipping sleeve. The distance between the front face of the crankshaft rear seal and the rear face of the cylinder block must be 15.4 0.5 mm (.61 .02 in) after seal installation. See the topic "Crankshaft Seals" in the 3114 & 3116 Diesel Truck Engines Specifications module, Form No. SENR6436 for further details.End By:a. install flywheel