Rating:
Information pump assy, supply Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IMELBUFF 294000-0610 294000-0611 294000-0613 22100-E0030 22100-E0031 22100-E0032 CR HP3 Fuel Injection Pump for Hino J05E J05E-TG Engine Kobelco SK200-8 SK260-8 Excavator
IMELBUFF 🚜Part Number: 294000-0610 294000-0611 294000-0613 22100-E0030 22100-E0031 22100-E0032 || 🚜Engine Model: for Hino J05E J05E-TG Engine || 🚜Application: for Kobelco Excavator SK200-8 SK260-8 || 🚜Warm Tips: Please check whether the fuel pump you need to replace match with us. If you are not sure, you can send us your model number. || 🚜Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product.
IMELBUFF 🚜Part Number: 294000-0610 294000-0611 294000-0613 22100-E0030 22100-E0031 22100-E0032 || 🚜Engine Model: for Hino J05E J05E-TG Engine || 🚜Application: for Kobelco Excavator SK200-8 SK260-8 || 🚜Warm Tips: Please check whether the fuel pump you need to replace match with us. If you are not sure, you can send us your model number. || 🚜Service: 5-months warranty and 24 hour support for customer service. Please feel free to contact us by email if you have any question with the product.
$509.99
14 Sep 2024
CN: CAR REFINE
Compatible with Kobelco Excavator SK200-8 Hino J05E Engine Fuel Pump Replacement Parts Fuel Injection Pump 22100-E0030 294000-0611 294000-0612 294000-0613 294000-0610
Podafu Part Number： 22100-E0030 294000-0610 294000-0618 294000-0611 294000-0612 294000-0613 294000-0614 294000-0615 294000-0616 294000-0617 294000-0619 22100-E0031 22100-E0032 22100-E0033 22100-E0034 22100-E0035 Fuel Pump || Application：For Kobelco Excavator SK200-8 SK250-8 SK260-8, for Hino 5.2L Diesel Engine J05E || By reducing fuel consumption, improving jitter, and enhancing speed smoothness, driving becomes more comfortable while also decreasing monthly fuel expenses. || Easy to install: Installation is fast and easy, requiring only a simple replacement process. || Make sure to confirm the part number and vehicle model to ensure that the product is compatible with your specific requirements.
Podafu Part Number： 22100-E0030 294000-0610 294000-0618 294000-0611 294000-0612 294000-0613 294000-0614 294000-0615 294000-0616 294000-0617 294000-0619 22100-E0031 22100-E0032 22100-E0033 22100-E0034 22100-E0035 Fuel Pump || Application：For Kobelco Excavator SK200-8 SK250-8 SK260-8, for Hino 5.2L Diesel Engine J05E || By reducing fuel consumption, improving jitter, and enhancing speed smoothness, driving becomes more comfortable while also decreasing monthly fuel expenses. || Easy to install: Installation is fast and easy, requiring only a simple replacement process. || Make sure to confirm the part number and vehicle model to ensure that the product is compatible with your specific requirements.
$501.00
12 Mar 2024
CN: yahegochengeg
shsiyayh Fuel Injection Pump 294000-0612 294000-0613 for Denso Hino J05E Engine Kobelco SK200-8 SK250-8 SK260-8 Excavator
shsiyayh Part Name:Fuel Injection Pump || Part Number:294000-0612 294000-0613 2940000612 2940000613 || APPlication: Compatible with Denso Hino J05E Engine Kobelco SK200-8 SK250-8 SK260-8 Excavator || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
shsiyayh Part Name:Fuel Injection Pump || Part Number:294000-0612 294000-0613 2940000612 2940000613 || APPlication: Compatible with Denso Hino J05E Engine Kobelco SK200-8 SK250-8 SK260-8 Excavator || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
29400-00613
22100-E003
PUMP ASSY, SUPPLY
Information:
1. Remove four bolts (3) that hold elbow (1) to the inlet manifold. Remove elbow (1) and inlet pipe (2) as a unit. 2. Remove bolts (5) that hold the valve cover bases to the cylinder head. Remove valve cover bases (4). It will be necessary to disconnect the wire clips from the inner fuel injection lines for the precombustion chamber engines. 3. Remove inner fuel injection lines (6). Install caps and plugs on all injection line openings. 4. Remove bolts (7) that hold the rocker shafts to the cylinder head.5. Remove rocker shafts (8). 6. Remove push rods (9) from the valve lifters. 7. Remove bridges (10) from the dowels on the cylinder head.Install Rocker Shafts And Push Rods
1. Put clean engine oil on the bridges and dowels. 2. Install the bridges (1) on the dowels. Keep pressure by hand on the bridges and turn the adjustment screw clockwise until contact is made with the valve stem. Turn the screw an extra 20° to 30°. This will make dowel straight in guide and make compensation for gap (slack) in the threads. Hold adjustment screw in this position and tighten locknut to a torque of 22 3 lb.ft. (28 4 N m). 3. Install push rods (2). 4. Put rocker shafts (3) in position on the cylinder head.5. Put clean engine oil on the threads of the bolts that hold the rocker shafts in place. Tighten the bolts first to a torque of 200 20 lb.ft. (270 25 N m). Start with the bolt in the center of the rocker shaft. Tighten bolts again to a torque of 330 15 lb.ft. (450 20 N m). Tighten bolts again by hand to a torque of 330 15 lb.ft. (450 20 N m).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (4). Tighten the fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m) with tool (A) and (B). Connect wire clips to the fuel injection lines for the precombustion chamber engines.7. Make an adjustment to the valves to have a clearance of .015 in. (0.38 mm) for intake and .030 in. (0.76 mm) for the exhaust. Tighten the locknuts to a torque of 22 3 lb.ft. (28 4 N m) and check the valve clearance again. 8. Install valve cover bases (6) on the cylinder head. Install bolts (5) that hold the valve cover bases in place. Tighten the bolts to a torque of 120 24 lb.in. (13.6 2.8 N m). 9. Put clean oil on the O-ring seal on inlet pipe (8). Install inlet pipe (8) into the turbocharger. Make sure the gasket for elbow (7) is in position on the inlet manifold. Install four bolts that hold elbow (7) to the inlet manifold.end by:a) install valve covers
1. Put clean engine oil on the bridges and dowels. 2. Install the bridges (1) on the dowels. Keep pressure by hand on the bridges and turn the adjustment screw clockwise until contact is made with the valve stem. Turn the screw an extra 20° to 30°. This will make dowel straight in guide and make compensation for gap (slack) in the threads. Hold adjustment screw in this position and tighten locknut to a torque of 22 3 lb.ft. (28 4 N m). 3. Install push rods (2). 4. Put rocker shafts (3) in position on the cylinder head.5. Put clean engine oil on the threads of the bolts that hold the rocker shafts in place. Tighten the bolts first to a torque of 200 20 lb.ft. (270 25 N m). Start with the bolt in the center of the rocker shaft. Tighten bolts again to a torque of 330 15 lb.ft. (450 20 N m). Tighten bolts again by hand to a torque of 330 15 lb.ft. (450 20 N m).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (4). Tighten the fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m) with tool (A) and (B). Connect wire clips to the fuel injection lines for the precombustion chamber engines.7. Make an adjustment to the valves to have a clearance of .015 in. (0.38 mm) for intake and .030 in. (0.76 mm) for the exhaust. Tighten the locknuts to a torque of 22 3 lb.ft. (28 4 N m) and check the valve clearance again. 8. Install valve cover bases (6) on the cylinder head. Install bolts (5) that hold the valve cover bases in place. Tighten the bolts to a torque of 120 24 lb.in. (13.6 2.8 N m). 9. Put clean oil on the O-ring seal on inlet pipe (8). Install inlet pipe (8) into the turbocharger. Make sure the gasket for elbow (7) is in position on the inlet manifold. Install four bolts that hold elbow (7) to the inlet manifold.end by:a) install valve covers