19100-08634 PUMP ASSY, INJECTI Calibration Data


Rating:
52
Buy PUMP ASSY, INJECTI 19100-08634 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
NB6,R901
01.002
BODY ASSY, INJECTI
NB6
02.003
COVER, BEARING
DUMMY
01.004
GOVERNOR ASSY, MEC
R901
02.005
LEVER SET
ADJUST L
02.006
COMPENSATOR SUB-AS
01.007
TIMER ASSY, AUTOMA
SA2 -9101
01.007
TIMER ASSY, AUTOMA
SA2 9101-
01.008
TIMER ASSY, AUTOMA
SA2 -9101
01.008
TIMER ASSY, AUTOMA
SA2 9101-
01.009
PUMP ASSY, FUEL FE
KD
01.010
COUPLING ASSY
SD

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19100-08634
PUMP ASSY, INJECTI
NB6,R901
ME076766 MITSUBISHI
003
[01]
BODY ASSY, INJECTI
NB6
ME728591 MITSUBISHI
004
[01]
GOVERNOR ASSY, MEC
R901
ME728918 MITSUBISHI
005
[01]
TIMER ASSY, AUTOMA
SA2 -9102
ME728593 MITSUBISHI
005
[01]
TIMER ASSY, AUTOMA
SA2 9102-
ME728599 MITSUBISHI
006
[01]
NUT, TIMER ROUND
M18X1.5
ME728343 MITSUBISHI
007
[01]
COUPLING ASSY
SD
ME728335 MITSUBISHI
008
[01]
KEY, WOODRUFF
W5,H7.5
ME702920 MITSUBISHI
009
[01]
PUMP ASSY, FUEL FE
KD
ME728536 MITSUBISHI
010
[01]
COVER, CONTROL RAC
ME728594 MITSUBISHI
011
[01]
WASHER, COPPER PLA
T1.5
ME039681 MITSUBISHI
012
[01]
BOLT
M6,L10 -9202
ME728595 MITSUBISHI
012
[01]
BOLT, W/WASHER
M8,L20 9202-
ME728979 MITSUBISHI
013
[04]
BOLT
M8,L16 -9202
ME728336 MITSUBISHI
013
[04]
BOLT, W/WASHER
M8,L16 9202-
ME728978 MITSUBISHI
014
[01]
BOLT
M8,L22 -9202
ME728596 MITSUBISHI
014
[01]
BOLT, W/WASHER
M8,L22 9202-
ME728980 MITSUBISHI
015
[02]
BOLT
M8,L14 -9202
ME728597 MITSUBISHI
015
[02]
BOLT, W/WASHER
M8,L14 9202-
ME728977 MITSUBISHI
016
[08]
WASHER, PLATE, SK
T1 -9202
ME728337 MITSUBISHI
019
[01]
CAP
ME035845 MITSUBISHI
021
[01]
CLIP, CORD
-9103
ME728198 MITSUBISHI
021
[01]
CAP
9103-
ME076458 MITSUBISHI

Include in ##:

19100-08634 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19100-08634 
ME076766 
PUMP ASSY, INJECTI

Test Calibration Data:

1910008634 MEO76766




Information:

Measure wear of the cylinder bore at the top and bottom of piston ring travel.(1) Cylinder bore [standard, original size] ... 4.5005 .0005 in.(114.313 0.013 mm) The recommendation is made to make the cylinder bore the next size larger when the size of the bore is ... 4.5060 in.(114.452 mm)Cylinder bore must be made the next size larger when the size of the bore is ... 4.5090 in.(114.529 mm)Cylinder bore [.020 in. (0.51 mm) larger than the original size] ... 4.5205 .0005 in.(114.821 0.013 mm)The recommendation is made to make the cylinder bore the next size larger when the size of the bore is ... 4.5260 in.(114.960 mm)Cylinder bore must be made the next size larger when the size of the bore is ... 4.5290 in.(115.037 mm)Cylinder bore [.040 in. (1.02 mm) larger than the original size] ... 4.5405 .0005 in.(115.329 0.013 mm)Maximum permissible wear of cylinder bores (replacement of the cylinder block is necessary) ... 4.5490 in.(115.545 mm)(2) Bore in block for camshaft bearing ... 2.6525 .0005 in.(67.374 0.013 mm)(3) Width of main bearing cap ... 6.5600 .0005 in.(116.624 0.013 mm) Minimum permissible width of main bearing cap ... 6.5580 in.(116.573 mm)Width of main bearing cap guide (in cylinder block) ... 6.5590 .0005 in.(116.599 0.013 mm)(4) Bore in block for main bearing ... 3.7075 .0005 in.(94.171 0.013 mm) Permissible amount of distortion in bore ... 3.706 to 3.709 in.(94.13 to 94.21 mm)(5) Torque for bolts holding caps for main bearings: A. Put crankcase oil on bolt threads and washer face.B. Tighten all bolts by number to ... 60 15 lb. ft.(8.3 2.0 mkg)C. Again tighten all bolts by number to ... 175 10 lb. ft.(24.2 1.4 mkg)Engines with Serial Numbers 98M2494 and Up, tighten bolts (5) holding caps for main bearings in the following sequence: 1. Put crankcase oil on bolt threads and washer face.2. Tighten all bolts by number to ... 30 3 lb. ft.(4.1 0.4 mkg)3. Put a mark on each bolt and cap.4. Tighten all bolts by number from mark ... 120° 5°

Have questions with 19100-08634?





Group cross 19100-08634

Back to top