19100-08543 PUMP ASSY, INJECTI Calibration Data


Rating:
14
Buy PUMP ASSY, INJECTI 19100-08543 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
NF6,R801
01.002
BODY ASSY, INJECTI
NF6
02.003
COVER, BEARING
DUMMY
01.004
GOVERNOR ASSY, MEC
R801
02.005
LEVER SET
ADJUST L
02.006
COVER ASSY, GOVERN
01.007
TIMER ASSY, AUTOMA
SA1
01.008
PUMP ASSY, FUEL FE
KE
01.009
PUMP ASSY, FUEL FE
KE
01.010
PUMP ASSY, FUEL FE
KE
01.011
COUPLING ASSY
SD

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19100-08543
PUMP ASSY, INJECTI
NF6,R801
22010-6421 HINO
003
[01]
PUMP ASSY, FUEL FE
KE -9009
22570-1430A HINO
003
[01]
PUMP ASSY, FUEL FE
KE22 9010--9803
22570-1500A HINO
003
[01]
PUMP ASSY, FUEL FE
KE 9804-
22570-1730A HINO
004
[01]
VALVE ASSY, OVERFL
1.5-1.8K -9009
22107-1290A HINO
004
[02]
VALVE ASSY, OVERFL
9010-
22107-1430A HINO
005
[02]
WASHER
T1
22847-1940A HINO
006
[01]
COVER, CONTROL RAC
-9502
22114-1250A HINO
006
[01]
COVER, CONTROL RAC
9503-
22118-1120 HINO
007
[05]
BOLT, W/WASHER
M6,L16
22815-2410A HINO
009
[01]
BOLT, W/WASHER
M6,L20
22815-1290A HINO
010
[01]
CAP
FOR MAX.SPEED
22323-1210A HINO
011
[01]
BOLT, W/WASHER
M8,L18
22815-2820A HINO
012
[01]
BODY ASSY, INJECTI
NF6
22110-2532A HINO
013
[01]
COUPLING ASSY
SD
22610-1640A HINO
014
[01]
NUT, TIMER ROUND
22511-1060A HINO
015
[01]
TIMER ASSY, AUTOMA
22510-2350A HINO
016
[01]
WASHER, COUNTERSUN
T1.5ID14
22867-1320A HINO
017
[01]
KEY, WOODRUFF
W4,H5
22895-1080A HINO
018
[01]
GOVERNOR ASSY, MEC
-9108
018
[01]
GOVERNOR ASSY, MEC
9108--9209
018
[01]
GOVERNOR ASSY, MEC
9209-
019
[01]
CLIP, CORD
FOR FULL-LOAD -9405
22323-1190A HINO
023
[01]
CAP
FOR FULL-LOAD 9406-
22323-1320A HINO

Include in ##:

19100-08543 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19100-08543 
22010-6421 
PUMP ASSY, INJECTI

Test Calibration Data:

1910008543 22010-6421A




Information:

Specification
Construction
Governor System Component Parts(1) Sealing metal(2) Sealing wire(3) Low- and high-speed(4) Governor spring(5) Sliding shaft(6) Stopper(7) Governor spring(8) Governor shaft(9) Governor lever(10) Tie-rod(11) Tie-rod clip(12) Tie-rod cover(13) tie-rod cover gasket(14) Tension lever(15) Start spring(16) Governor spring lever(17) Speed control lever assembly(18) Cover assembly(19) Governor cover gasket(20) Return spring(21) Stop lever assembly(22) O-ring(23) Snap ring(24) Stop lever(25) Grooved pin (3 x 20)(26) Grooved pin (3 x 14)(27) Torque spring set(28) Sealing capTORQUE SPRING
Installation of Torque Spring Set
Install and adjust the torque spring set using the following procedure:(1) Set the speed control lever to the high-idling speed position by adjusting the high-speed set bolt.(2) Turn in the torque spring set until engine speed drops about 50 rpm from high-idling speed.(3) From this position, turn back the torque spring set by the specified number of turns (N.) Lock the torque spring set at that position with the special nut.(4) Install the torque spring set sealing cap and stake the cap to prevent loosening. CAUTION There are two types of torque spring set: The single spring type and the double-spring type. Since each torque spring set has been adjusted precisely during assembly, do not tamper with the adjust screw unless it is necessary.
Torque spring setAssembling the Torque Spring Set
When the torque spring set has been disassembled or its component parts have been replaced, reassemble and adjust the torque spring set using the following procedure:
Assembling torque spring setSingle spring type
When installing the single-spring type torque spring set, use the following steps.(1) Lightly turn in adjust screw (5) (with a screw-driver operated by fingertips) until a resistance to screw rotation is felt. Lightly lock the screw at that position with locknut (4).(2) Set the scale to the zero-point. Turn in the spring case (2) until the value of load "A" shown in table below can be attained. Lock the spring case at that position with special nut (3).(3) Temporarily loosen adjust screw (5) until the value of load "A" is reduced by about 200 grams, and then retighten the screw until the value of "B" is attained. Lock the screw at that position with locknut (4).Adjust screw tightening torque: 0.8 to 1.2 kg.(4) To inspect the torque spring set for properly adjusted spring load, use a testing arrangement such as shown in the figure at right. Gradually push the scale against the torque spring set until the stopper (1) is moved (or the pointer of dial gauge deflects). Check that the load applied to the torque spring at that moment coincides with the value of load "C".
Setting of Torque Spring CHECKING
Replace the gear case and inspect the governor. When removing the gear case, be sure to remove the tie-rod cover by the side of the fuel pump and disconnect the tie-rod from the rack.If any parts are found defective, replace them.
Inspecting Torque Spring CAUTION When the governor is assumed to be malfunctioning, check the bearing on the gear case side, too.
Inspection Governor System PartsRemoval and Installation
(Refer to I-06 GEAR CASE AND OIL PUMP.)Removal(1) Removing

Have questions with 19100-08543?





Group cross 19100-08543

Back to top