19100-03460 PUMP ASSY, INJECTI Calibration Data


Rating:
70
Buy PUMP ASSY, INJECTI 19100-03460 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
Construction machine 6D125
Engine
6D125
Serial start-end
8609--9205
Info
Injector Nozzle
093500-2710
Injector nozzle: 0935002710

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Pump assy, fuel fe
Governor assy, mec

Components :

00.001
PUMP ASSY, INJECTI
NB6,RSV
01.002
BODY ASSY, INJECTI
NB6
02.003
COVER, BEARING
DUMMY
01.004
PUMP ASSY, FUEL FE
KE
01.005
COUPLING ASSY
SD
01.006
GOVERNOR ASSY, MEC
RSV -8810
01.006
GOVERNOR ASSY, MEC
8811-

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
NB6,RSV
003
[01]
BODY ASSY, INJECTI
NB6
004
[01]
GOVERNOR ASSY, MEC
RSV
005
[02]
BOLT, W/WASHER
M6,L14
006
[01]
COVER, CONTROL RAC
007
[01]
NUT, TIMER ROUND
008
[01]
WASHER, COUNTERSUN
T1.5ID18
009
[01]
KEY, WOODRUFF
W5,H7.5
010
[01]
PUMP ASSY, FUEL FE
KE22
011
[01]
COVER, PRIMING PUM
012
[01]
WASHER, COPPER PLA
T1.5
014
[01]
COUPLING ASSY
SD
015
[02]
WASHER, FUEL PIPE
T1.2
016
[01]
VALVE ASSY, OVERFL
1.5-1.7K
017
[02]
BOLT, W/WASHER
M6,L20
018
[04]
BOLT, W/WASHER
M6,L16

Cross reference number



Part num
Firm num
Firm
Name
19100-03460 
 
PUMP ASSY, INJECTI

Test Calibration Data:

1910003460 6150-71-2611




Information:

1. Remove four bolts and shield (1). Remove two bolts and screen (2). Disconnect ground strap (3) from the generator mounting bracket. Remove two generator mounting bolts (4). 2. Loosen front engine mounting bolts (5) to provide clearance to raise the rear of the engine. 3. Attach a hoist to generator (6). Raise the generator and the engine so the generator mounting pads are off of the supports. Put blocks under the flywheel housing to support the rear of the engine as shown. 4. Remove bolts (7) that hold fan (9) to the flywheel. Remove bolts (8) that hold the generator housing to the flywheel housing and remove the generator. The weight of the generator is approximately 1130 kg (2500 lb.).Connection Of Engine And Generator (Prime)
The following procudure applies to the 3406B Standby Generator also. 1. Remove the protection material (compound) from the flywheel pilot bore (10) and from the surface (11) that makes contact with the coupling. All contact surfaces of the engine, coupling and generator must be completely clean. 2. Install tooling (A) as shown on the front of the engine with the tip of the indicator on the face of crankshaft pulley (12). Use a bar between the flywheel and flywheel housing to push the crankshaft toward the flywheel to remove all end play. Put the dial indicator in the "zero" position. Move the crankshaft to its most forward position, and make a record of the Total Indicator Reading (TIR). The TIR is the end play of the crankshaft. 3. Put plate assembly (13) in position in the bore of the flywheel to check for clearance. There must be clearance between the outside diameter of the plate assembly (13) and the inside diameter of the bore in the flywheel.
Damage to the engine and/or generator can be the result if the electric set is run with a plate assembly that does not have this clearance.
4. Install full shim pack (14) and plate assembly (13) on the generator with bolts (15).5. Install a guide bolt in the flywheel. Put the generator in position on the engine, and install bolts (7) and (8).6. Use tooling (A) to check crankshaft end play. Do not use force to hold the crankshaft in position. Remove the generator. Remove only enough shims to get the original amount of end play as shown in Step 2. The minimum crankshaft end play should be 0.15 mm (0.006 in.).7. Install the generator and check the crankshaft end play again. If the end play is correct, attach a hoist to the generator and remove the blocks from under the flywheel housing.8. Lower the generator on to the supports and install bolts (4). Connect ground strap (3) to the generator. Install screen (2) and shield (1).9. Tighten fron engine mounting bolts (5).End By:a. install control panel enclosure

Have questions with 19100-03460?





Group cross 19100-03460

Back to top