19100-03340 PUMP ASSY, INJECTI Calibration Data


Rating:
67
Buy PUMP ASSY, INJECTI 19100-03340 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL S6D125
Engine
S6D125
Serial start-end
8609-
Info
Injector Nozzle
093500-3610
Injector nozzle: 0935003610

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Pump assy, fuel fe
Governor assy, mec

Components :

00.001
PUMP ASSY, INJECTI
NB6,RSV
01.002
BODY ASSY, INJECTI
NB6
02.003
COVER, BEARING
DUMMY
01.004
PUMP ASSY, FUEL FE
KE
01.005
COUPLING ASSY
SD
01.006
GOVERNOR ASSY, MEC
RSV -8810
01.006
GOVERNOR ASSY, MEC
8811-

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
NB6,RSV
003
[01]
BODY ASSY, INJECTI
NB6
004
[01]
GOVERNOR ASSY, MEC
RSV
005
[02]
BOLT, W/WASHER
M6,L14
006
[01]
COVER, CONTROL RAC
007
[01]
NUT, TIMER ROUND
008
[01]
WASHER, COUNTERSUN
T1.5ID18
009
[01]
KEY, WOODRUFF
W5,H7.5
010
[01]
PUMP ASSY, FUEL FE
KE22
011
[01]
COVER, PRIMING PUM
012
[01]
WASHER, COPPER PLA
T1.5
014
[01]
COUPLING ASSY
SD
015
[02]
WASHER, FUEL PIPE
T1.2
016
[01]
VALVE ASSY, OVERFL
1.5-1.7K
017
[02]
BOLT, W/WASHER
M6,L20
018
[04]
BOLT, W/WASHER
M6,L16

Cross reference number



Part num
Firm num
Firm
Name
19100-03340 
 
PUMP ASSY, INJECTI

Test Calibration Data:

1910003340 6151-71-1550




Information:

2. Turn the crankshaft until two pistons are at bottom center.3. Remove nuts (1) and the bearing caps. Push the rods and pistons up until the rings are out of the cylinder liners. 4. Remove pistons (2) and connecting rods from the cylinder liners.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.Install Pistons And Connecting Rod Assemblies
1. Put clean engine oil on piston rings, connecting rod bearings and cylinder liners. 2. Use tool (A), and install piston (2) and the connecting rod in the cylinder liner. Be sure the number on the tab groove side of the connecting rod is on the opposite side from the camshaft.3. Install the bearing cap on the connecting rod with the number on the side of the bearing cap on the same side and same number as on the connecting rod.4a. For connecting rods with bolts and nuts, use the following torque procedure: Apply clean engine oil to the bolt threads, nuts, and seating faces of the bearing cap. Tighten each nut to a torque of 80 5 N m (60 4 lb.ft.). Tighten each nut an additional 120° 5°.4b. For connecting rods with only bolts, use the following torque procedure: Apply Molylube to the threads of the bolts and to the seating faces of the bearing cap and the bolt. Tighten each bolt to a torque of 90 8 N m (66 6 lb.ft.). Tighten each bolt an additional 90° 5°.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.End By:a. install oil pumpb. install cylinder head assembly.Disassemble And Assemble Pistons And Connecting Rod Assemblies
Start By:a. remove pistons and connecting rod assemblies 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) and tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See, Use Of Piston Pin Bearing Removal And Installation Tools, Special Instructions, Form No. SMHS7295.5. Heat connecting rod (4) in an oven to a temperature of 177° to 260° C (350° to 500° F). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.7. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 50.830 0.008 mm (2.0012 .0003 in.).9. Check the clearance between the ends of the piston rings. See

Have questions with 19100-03340?





Group cross 19100-03340

Back to top