19000-09110 PUMP ASSY, INJECTI Calibration Data


Rating:
45
Buy PUMP ASSY, INJECTI 19000-09110 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 6D125
Engine
6D125
Serial start-end
8311--9402
Info
Injector Nozzle
093500-2710
Injector nozzle: 0935002710

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Body assy, injecti
Body assy, injecti
Governor assy, mec
Pump assy, fuel fe
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
NB6,RSV -0010
00.001
PUMP ASSY, INJECTI
NB6,RSV 0010-
01.002
BODY ASSY, INJECTI
NB6
02.003
COVER, BEARING
DUMMY
01.004
BODY ASSY, INJECTI
NB6
01.005
BODY ASSY, INJECTI
NB6
01.006
GOVERNOR ASSY, MEC
-8502
01.006
GOVERNOR ASSY, MEC
8503--8810
01.006
GOVERNOR ASSY, MEC
8811-
01.007
PUMP ASSY, FUEL FE
KE
01.008
PUMP ASSY, FUEL FE
KE
01.009
COUPLING ASSY
SD

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
NB6,RSV -0010
000
[01]
PUMP ASSY, INJECTI
NB6,RSV 0010-
003
[01]
BODY ASSY, INJECTI
NB6 -8502
003
[01]
BODY ASSY, INJECTI
NB6 8503--8511
003
[01]
BODY ASSY, INJECTI
NB6 8511--8701
003
[01]
BODY ASSY, INJECTI
NB6 8701-
004
[01]
GOVERNOR ASSY, MEC
RSV
005
[02]
BOLT, W/WASHER
M6,L14
006
[01]
COVER, CONTROL RAC
007
[01]
NUT, TIMER ROUND
008
[01]
WASHER, COUNTERSUN
T1.5ID18
009
[01]
KEY, WOODRUFF
W5,H7.5
010
[01]
PUMP ASSY, FUEL FE
KE -8502
010
[01]
PUMP ASSY, FUEL FE
KE 8503-
011
[01]
COVER, PRIMING PUM
012
[01]
WASHER, COPPER PLA
T1.5
014
[01]
COUPLING ASSY
SD
015
[02]
WASHER, FUEL PIPE
T1.2
016
[01]
VALVE ASSY, OVERFL
1.5-1.7K
017
[02]
BOLT, W/WASHER
M6,L20
018
[04]
BOLT, W/WASHER
M6,L16

Cross reference number



Part num
Firm num
Firm
Name
19000-09110 
 
PUMP ASSY, INJECTI

Test Calibration Data:

1900009110 6150-71-1511




Information:

Start By:a. remove valve covers 1. Use tooling (A), and disconnect fuel line (1) at each end. Remove the fuel line from the engine. 2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. Install the 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and on seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tooling (A) to a torque of 40 7 N m (30 5 lb.ft.).End By:a. install valve covers

Have questions with 19000-09110?





Group cross 19000-09110

Back to top