19000-07190 PUMP ASSY, INJECTI Denso Cross


Rating:
68
Buy PUMP ASSY, INJECTI 19000-07190 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 2J
Engine
2J
Serial start-end
8312--8903
Info
Injector Nozzle
093500-1810
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Timer assy, automa

Components :

00.001
PUMP ASSY, INJECTI
A4,MN
01.002
BODY ASSY, INJECTI
A4:COLD SPEC OLD
01.003
TIMER ASSY, AUTOMA
01.003
TIMER ASSY, AUTOMA
SCZ
01.004
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-07190
PUMP ASSY, INJECTI
A4,MN
22100-97326-71 TOYOTA
001
[01]
BODY ASSY, INJECTI
A4
002
[01]
GOVERNOR ASSY, INJ
MN
003
[01]
PUMP ASSY, FUEL FE
KE
22510-97236-71 TOYOTA
006
[01]
KEY, WOODRUFF
007
[01]
WASHER, SPRING
T3
008
[01]
NUT, TIMER ROUND
D16,L15
009
[01]
SHAFT, SPLINE
010
[04]
BOLT, W/WASHER
M6,L16
012
[01]
BOLT, W/WASHER
M8,L22
015
[01]
COVER, CONTROL RAC
016
[01]
COVER, PRIMING PUM
017
[01]
WIRE, OVER, INJECT
22175-46010 TOYOTA
020
[01]
TIMER ASSY, AUTOMA
SCZ

Include in ##:

19000-07190 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-07190 
22100-9732 
PUMP ASSY, INJECTI
1900007190 
22100-97326-71 
TOYOTA
PUMP ASSY, INJECTI




Information:

Possible Causes/Corrections
Dirty Air CleanerIf the air cleaner has a restriction indicator, see if the red piston is in view. If there is no restriction indicator, restriction can be checked with a water manometer or a vacuum gauge (which measures in inches of water). Make a connection to the piping between the air cleaner and the inlet of the turbocharger. Check with the engine running at full load rpm. Maximum restriction is 635 mm (25 in) of water. If a gauge is not available, visually check the air cleaner element for dirt. If the element is dirty, clean the element or install a new element. Air Inlet Piping Damage Or RestrictionMake a visual inspection of the air inlet system and check for damage to piping, rags in the inlet piping, or damage to the rain cap or the cap pushed too far on the inlet pipe. If no damage is seen, check inlet restriction with a clean air cleaner element. Exhaust System RestrictionMake a visual inspection of the exhaust system. Check for damage to piping or for a defective muffler. If no damage is found, you can check the system by checking the back pressure from the exhaust (pressure difference measurement between exhaust outlet and atmosphere). The back pressure must not be more than 1016 mm (40 in) of water. You can also check by removing the exhaust pipes from the exhaust manifolds. With the exhaust pipes removed, start and load the engine on a chassis dynamometer to see if the problem is corrected. Fuel Injection Timing Not CorrectCheck and make necessary adjustments as in Testing and Adjusting Section of this Service Manual. Fuel Setting Is Not CorrectCheck and make necessary adjustments as in Testing and Adjusting Section of this Service Manual. See the Fuel Setting And Related Information Fiche for the correct fuel setting. Low Quality FuelTest the engine with fuel according to recommendations by Caterpillar Inc. For more information see Special Instruction, Form No. SEHS7067, Fuel Recommendations For Caterpillar Diesel Engines. Also, Special Instruction, Form No. SEHS6947 has fuel correction factors and tables. Defective Fuel Nozzle(s)Defective fuel nozzles will normally cause the engine to misfire and run rough, but can cause too much smoke with engine still running smooth. Remove the fuel nozzles and test as in Testing and Adjusting Section of this Service Manual. Wrong Seal Washer Installed Under Nozzle(s)The use of incorrect washers change the location of the fuel injection nozzles in the combustion chamber. This effects smoke. Check the Engine Arrangement for the correct part number to use. Valve Adjustment Not Correct Or Valve LeakageCheck and make necessary adjustments as in Testing and Adjusting Section of this Service Manual. Intake valve lash is 0.38 mm (.015 in) and exhaust valve lash is 0.64 mm (.025 in). Valve leakage normally causes the engine to misfire and run rough. Defective Fuel Injection PumpAn injection pump can have a good fuel flow coming from it but cause rough running because of slow timing that is caused by

Have questions with 19000-07190?





Group cross 19000-07190

Back to top