19000-06230 TOYOTA PUMP ASSY, INJECTI Denso Cross


Rating:
72
Buy PUMP ASSY, INJECTI 19000-06230 TOYOTA genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
DYNA 2H
Engine
2H
Serial start-end
8110--8301
Info
Injector Nozzle
093500-1810
TOYOTA PUMP ASSY, INJECTI AA
  • * THIS PUMP IS A SPAIR PUMP OF 093000-0270
  • (WITHOUT TIMER).
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A6,COMB
01.002
BODY ASSY, INJECTI
A6
01.003
TIMER ASSY, AUTOMA
01.004
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-06230
PUMP ASSY, INJECTI
A6,COMB
22100-68090 TOYOTA
001
[01]
BODY ASSY, INJECTI
A6,OLD
22120-68010 TOYOTA
002
[01]
GOVERNOR ASSY, COM
COMBINED
22320-68090 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
22510-77130 TOYOTA
004
[01]
TIMER ASSY, AUTOMA
SCZ
26106-8020 TOYOTA
007
[01]
COVER, CONTROL RAC
22116-46010 TOYOTA
008
[01]
KEY, WOODRUFF
90099-13020 TOYOTA
009
[01]
NUT, TIMER ROUND
22611-68010 TOYOTA
010
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
011
[04]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA
014
[01]
COVER SUB-ASSY, TI
22812-68010 TOYOTA
015
[04]
NUT, HEXAGON
M10
94110-41000 TOYOTA
016
[04]
WASHER, STEEL PLAT
ID10,T4 -8903
90201-10018 TOYOTA
016
[04]
WASHER, STEEL PLAT
FOR M10 8904-
90099-01468 TOYOTA

Include in ##:

19000-06230 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-06230 
22100-6809 
TOYOTA
PUMP ASSY, INJECTI
1900006230 
22100-68090 
TOYOTA
PUMP ASSY, INJECTI




Information:

The turbocharger does not have to be removed from the engine in order to remove the wastegate.1. Remove two clamps (1) and hose (2). 2. Remove retainer (4) and two nuts (3). 3. Remove three mounting bolts (6) and bracket (5).Disassemble Turbocharger (Schweitzer S4A)
Start By:a. remove turbocharger 1. Install the turbocharger on tool (A) as shown.2. Put alignment marks on three housings of the turbocharger for correct alignment during assembly. Loosen clamp (2), and remove the clamp and housing (1) from housing assembly (3). 3. Loosen clamp (4), and remove housing assembly (3) from housing (5). 4. Put the cartridge group in position in tool (B) as shown.
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
5. Use a 5S9566 Sliding T-Wrench and a universal socket (6) to remove the nut that holds the compressor wheel to the wheel assembly.6. Remove compressor wheel (7) and the shims from wheel assembly (8).7. Remove housing assembly (3). 8. Remove ring (9) and backplate (10). 9. Use tool (C), and remove snap ring (11). 10. Remove insert (12) and sleeve (13). 11. Remove ring (14). 12. Remove two screws (15) and deflector (16). 13. Remove ring (18) and bearing assembly (17). 14. Remove sleeve (19) and ring (20). 15. Remove O-ring seal (23). Use tool (D), and remove snap ring (22).16. Remove bearing (21). Remove the snap ring behind the bearing with tool (D). 17. Use tool (D), and remove snap ring (25). Remove bearing (24). Remove the snap ring behind the bearing with tool (D).18. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction, Form No. SMHS6854, for Turbocharger Reconditioning. Also, see Guidelines For Reusable Parts, Form No. SEBF8018.Assemble Turbocharger (Schweitzer S4A)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, pour clean engine oil into the oil inlet of the turbocharger.
Make sure that the snap rings that hold bearings (24) and (21) in position in housing assembly (3) are installed with the round edge of the outside diameter toward the bearing.
2. Install the snap ring behind bearing (24) with tool (D). Install bearing (24).3. Use tool (D), and install snap ring (25). 4. Install the snap ring behind bearing (21) with tool (D). Install bearing (21).5. Use tool (D), and install snap ring (22). 6. Put wheel assembly (8) in position on tool (B) as shown. Put backplate (10) in position on the wheel assembly. Put 6V2055 High Vacuum Grease in the groove for seal ring (9) at assembly to one half or more of the depth of the groove all the way around.7. Install ring (9) in the groove in wheel assembly (8). 8. Install housing

Have questions with 19000-06230?





Group cross 19000-06230 TOYOTA

Back to top