19000-05790 PUMP ASSY, INJECTI Denso Cross


Rating:
47
Buy PUMP ASSY, INJECTI 19000-05790 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 2H
Engine
2H
Serial start-end
8108--9305
Info
Injector Nozzle
093500-1810
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Governor assy, mec
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A6,RUV
01.002
BODY ASSY, INJECTI
A6,OLD
01.003
GOVERNOR ASSY, MEC
RUV
01.004
PUMP ASSY, FUEL FE
01.004
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
A6,RUV
22100-42200-71 TOYOTA
001
[01]
BODY ASSY, INJECTI
A6,OLD
002
[01]
GOVERNOR ASSY, MEC
RUV
22410-31960-71 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
004
[01]
SHAFT, SPLINE
007
[01]
NUT, TIMER ROUND
010
[01]
COVER, CONTROL RAC
011
[01]
WASHER, SPRING
T3
012
[06]
BOLT, W/WASHER
M6,L14
013
[01]
KEY, WOODRUFF

Cross reference number



Part num
Firm num
Firm
Name
19000-05790 
 
PUMP ASSY, INJECTI
1900005790 
22100-42200-71 
TOYOTA
PUMP ASSY, INJECTI




Information:


Typical Example1. With the rear of wire connector toward you, snap tool (A) (the correct size for the wire being removed) over the wire of the contact to be removed.2. Slide tool (A) along the wire into the contact cavity until it engages the contact and resistance is felt. Do not twist or insert tool (A) at an angle.
Typical Example3. Pull contact (2) and wire assembly out of connector (1).4. Remove the damaged contact from the wire.
Typical Example5. Use tool (B) and the following procedure to secure contact (2) to the wire.a. Strip 6.3 mm (.25 in.) insulation from the wire.b. Raise selector knob (3) and rotate until arrow is aligned with the wire size to be crimped.c. Loosen locknut. Turn adjusting screw (4) in (clockwise) until it stops.
Typical Exampled. Insert contact (2) into tool (B). Turn the adjusting screw out (counter clockwise) until the contact is flush with indentor cover (5) on tool (B). Tighten locknut.
Typical Examplec. Insert wire in contact (2). The contact must be centered between the indentors. Close the handles until the handle contacts the stop.d. Release the handles and remove the crimped contact.e. Inspect the contact to insure that all wire strands are inside the crimp barrel. Look in the hole in the contact. If the crimp is correct wire strands will be visable in the hole in the contact.
Typical Example6. Grasp the wire approximately 25.4 mm (1.00 in.) behind the contact crimp barrel.7. Hold connector (1) with the rear grommet facing you.8. Push contact (2) straight into connector (1) until a positive stop is felt.9. Gently pull on the wire and connector assembly to confirm that the contact is properly locked in place.

Have questions with 19000-05790?





Group cross 19000-05790

Back to top