19000-05202 PUMP ASSY, INJECTI Denso Cross


Rating:
25
Buy PUMP ASSY, INJECTI 19000-05202 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A6,R722
01.002
BODY ASSY, INJECTI
A6
02.003
COVER, BEARING
DUMMY
01.004
TIMER ASSY, AUTOMA
SA/2SP
01.005
PUMP ASSY, FUEL FE
KE
01.006
COUPLING ASSY
SP

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-05202
PUMP ASSY, INJECTI
A6,R722
22010-2651 HINO
006
[01]
BODY ASSY, INJECTI
A6
22110-1590C HINO
007
[01]
GOVERNOR ASSY, MEC
R722
008
[06]
BOLT, W/WASHER
M6,L14
6 306 1001 00 HINO
009
[01]
BOLT, W/WASHER
M8,L18
22815-2820A HINO
011
[01]
COVER, CONTROL RAC
22114-1020A HINO
012
[01]
TIMER ASSY, AUTOMA
SA/2SP
22510-1190A HINO
013
[01]
NUT, TIMER ROUND
22511-1070A HINO
014
[01]
KEY, WOODRUFF
T3.985
22895-1010A HINO
015
[01]
WASHER, SPRING
T3.5
22877-1620A HINO
016
[01]
PUMP ASSY, FUEL FE
KE
22570-1250A HINO
017
[01]
COVER, PRIMING PUM
22561-1020 HINO
018
[01]
COUPLING ASSY
SP
22610-1080A HINO
020
[01]
VALVE ASSY, OVERFL
1.5-1.7K
22107-1090A HINO
022
[02]
WASHER
T1,D15.9
22847-1940A HINO
023
[03]
NUT, HEXAGON
M6,L5
22825-1480A HINO
024
[03]
WASHER, SPRING
T1.5
28219-1110A HINO

Include in ##:

19000-05202 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-05202 
22010-2651 
PUMP ASSY, INJECTI




Information:


Do not use more than 55 kPa (8 psi) of air pressure in the fuel tank or damage to the tank may result.
Check for leaks at the connection between the fuel tank and the fuel transfer pump. If leaks are found, tighten the connections or replace the lines. If there are no visual leaks, remove the fuel supply line from the tank and connect it to an outside furl supply. If this corrects the problem, the suction line (standpipe) inside the fuel tank has a leak.Water in the fuel can cause rough running and possible fuel system damage. Valve Adjustment Not CorrectCheck and make necessary adjustments as in Testing And Adjusting Section of the Service Manual. Intake valve lash is 0.38 mm (.015 in) and exhaust valve lash is 0.64 mm (.025 in). Also check for a bent or broken push rod. Defective Fuel Nozzle(s)Find a defective nozzle by running engine at the rpm where it runs rough. Loosen the fuel line nut at the through the head adapter enough to stop fuel supply to that cylinder. Each cylinder must be checked this way. If a cylinder is found where loosening of the nut makes no difference in the rough running, test the nozzle for that cylinder. To test a nozzle, remove the nozzle from the engine and test as in Testing and Adjusting Section of this Service Manual. Fuel Leakage From Fuel Injection Line NutTighten nut to 40 7 N m (30 5 lb ft). Again check for leakage. Be sure to check fuel injection lines inside valve cover base. Defective Fuel Injection PumpAn injection pump can have a good fuel flow coming from it but cause rough running because of slow timing that is caused by wear on the bottom end of the plunger. See the Testing and Adjusting Section in this Service Manual for the correct specifications and procedure to check plungers and lifters.Fuel pumps which are severely scored from debris can cause rough running but fuel dilution usually occurs before horsepower is affected.Low installation torque on the fuel pump retaining nut can cause misfire, rough running and low power. Fuel Has A High "Cloud Point"In cold weather operation this condition should be checked first. The fuel "cloud point" is the temperature at which wax begins to form in the fuel. If the atmospheric temperature is lower than the "cloud point" of the fuel, wax will form and plug the filter. Change the filter and drain the tank and the complete fuel system. The replacement fuel must be of a better grade with a lower "cloud point". Fuel Injection Timing Not CorrectCheck and make necessary adjustments as in Testing and Adjusting Section of this Service Manual. Automatic Timing Advance Does Not Operate CorrectlyCheck with engine warm. Use the 8T5300 Engine Timing Indicator Group and 8T5301 Diesel Timing Adapter Group. Special Instruction Form No. SEHS8580 has instructions and calibration procedures for this tool group. If the timing indicator group is not available, make rapid

Have questions with 19000-05202?





Group cross 19000-05202

Back to top