19000-04651 PUMP ASSY, INJECTI Calibration Data


Rating:
41
Buy PUMP ASSY, INJECTI 19000-04651 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A4 COMBINED
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
GOVERNOR ASSY, COM
COMBINED
01.004
TIMER ASSY, AUTOMA
SCZ
01.005
PUMP ASSY, FUEL FE
KE
01.005
PUMP ASSY, FUEL FE
KE22

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-04651
PUMP ASSY, INJECTI
A4 COMBINED
22100-58010 TOYOTA
003
[01]
COVER, CONTROL RAC
22116-46010 TOYOTA
004
[01]
BODY ASSY, INJECTI
A4
22120-58010 TOYOTA
005
[01]
GOVERNOR ASSY, COM
COMBINED
22320-58010 TOYOTA
006
[01]
PUMP ASSY, FUEL FE
KE
22510-56040 TOYOTA
009
[01]
NUT, TIMER ROUND
22611-46010 TOYOTA
010
[01]
WASHER, SPRING
T3
22173-46010 TOYOTA
011
[01]
SHAFT, SPLINE
22174-47010 TOYOTA
012
[01]
KEY, WOODRUFF
90099-13002 TOYOTA
013
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
014
[03]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA
015
[01]
BOLT, W/WASHER
M6,L12
90091-20607 TOYOTA
100
[01]
TIMER ASSY, AUTOMA
EXCLUDE
22610-56040 TOYOTA

Include in ##:

19000-04651 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-04651 
22100-5801 
PUMP ASSY, INJECTI

Test Calibration Data:

1900004651 22100-58010




Information:

Start By:a. remove flywheel housingb. remove oil pan platec. remove camshaft
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove the camshaft bearings from the cylinder block with tooling (A). Start with the front bearing and work to the rear. The following steps are for the installation of the camshaft bearings.2. Use tooling (A) to install the camshaft bearings in the cylinder block. 3. Install the camshaft bearings in the cylinder block as follows:a. Install the front bearing to a depth of 0.5 0.5 mm (.02 .02 in) and with the oil holes in a horizontal position and the joint at the top of the engine. The joint can not be more than 15° from vertical in either direction.b. Install the remainder of the bearings. Install the bearings to the dimensions given from the front face of the cylinder block: A) 154.0 0.5 mm (6.06 .02 in), B) 303.2 0.5 mm (11.94 .02 in), C) 601.7 0.5 mm (23.69 .02 in), D) 903.4 0.5 mm (35.57 .02 in).End By:a. install camshaftb. install oil pan platec. install flywheel housing
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.

Have questions with 19000-04651?





Group cross 19000-04651

Back to top