19000-03610 PUMP ASSY, INJECTI Denso Cross


Rating:
47
Buy PUMP ASSY, INJECTI 19000-03610 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
BUS A/C 2J
Engine
2J
Serial start-end
7910--8812
Info
Injector Nozzle
093500-1810
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Governor assy, inj
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A4,MZ
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
GOVERNOR ASSY, INJ
MZ
01.004
TIMER ASSY, AUTOMA
01.004
TIMER ASSY, AUTOMA
SCZ
01.005
PUMP ASSY, FUEL FE
01.005
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
A4,MZ
22100-78508-71 TOYOTA
001
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
002
[01]
GOVERNOR ASSY, INJ
MZ
003
[01]
PUMP ASSY, FUEL FE
KE
006
[01]
KEY, WOODRUFF
007
[01]
WASHER, SPRING
T3
008
[01]
NUT, TIMER ROUND
009
[01]
SHAFT, SPLINE
010
[03]
BOLT, W/WASHER
M6,L16
011
[01]
BOLT, W/WASHER
M6,L14
012
[01]
BOLT, W/WASHER
M8,L22
015
[01]
COVER, CONTROL RAC
016
[01]
WIRE, OVER, INJECT
22175-46010 TOYOTA
017
[01]
COVER, PRIMING PUM
020
[01]
TIMER ASSY, AUTOMA
EXCLUDE

Cross reference number



Part num
Firm num
Firm
Name
19000-03610 
 
PUMP ASSY, INJECTI
1900003610 
22100-78508-71 
TOYOTA
PUMP ASSY, INJECTI




Information:

1. Disconnect water supply hose from water pump inlet.2. Remove connector pipe (1), remove two bolts (2) and remove oil fill pipe (3). 3. Remove bolts (4) and (5) then remove the water pump. The following steps are for the installation of the water pump.4. Position the water pump and install two bolts (5) and (6). Tighten the two bolts evenly.5. Position connector pipe (1) and gaskets then install the bolts.6. Install oil fill pipe (3). Be sure the gasket is in position between the regulator and pipe and install bolts (2).End By:a. Install alternator (if removed)b. Fill the cooling system to the specified level. See the Maintenance Manual.Disassemble And Assemble Water Pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in.).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump

Have questions with 19000-03610?





Group cross 19000-03610

Back to top