19000-02821 PUMP ASSY, INJECTI Denso Cross


Rating:
19
Buy PUMP ASSY, INJECTI 19000-02821 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A6,RSV
01.002
BODY ASSY, INJECTI
A6
01.003
TIMER ASSY, AUTOMA
SCZ
01.004
PUMP ASSY, FUEL FE
KS

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-02821
PUMP ASSY, INJECTI
A6,RSV
003
[01]
BODY ASSY, INJECTI
A6
004
[01]
GOVERNOR ASSY, MEC
RSV
005
[01]
PUMP ASSY, FUEL FE
KS
006
[01]
TIMER ASSY, AUTOMA
SCZ
007
[01]
COVER SUB-ASSY, TI
008
[01]
O-RING
ID75
009
[04]
WASHER, SPRING
M10
010
[04]
WASHER, STEEL PLAT
FOR M10
011
[04]
NUT, HEXAGON
M10
012
[1C]
KEY, WOODRUFF
T4.023
012
[1C]
KEY, WOODRUFF
T4.013
012
[1C]
KEY, WOODRUFF
T4.003
012
[1C]
KEY, WOODRUFF
T3.998
013
[01]
WASHER, SPRING
T3.5
014
[01]
NUT, TIMER ROUND
015
[01]
COVER, CONTROL RAC
016
[05]
BOLT, W/WASHER
M6,L20
017
[01]
SCREW, CROSSRECESS
M8,L16

Include in ##:

19000-02821 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-02821 
 
PUMP ASSY, INJECTI




Information:

START BY:a. remove valve covers 1. Remove four bolts (1) from the turbocharger tube adapter to the aftercooler housing. Loosen the turbocharger compressor housing clamp, and rotate turbocharger tube (2) out of the way of the cylinder head assembly. 2. Remove bolts (3) that hold the valve cover bases to the cylinder head assembly. Remove valve cover bases (4).
To prevent damage to the fuel injection nozzle, hold adapter assembly (5) in position at the top of injection nozzle (6) when fuel line nut (7) is loosened or tightened.
3. Use tool (A) and a 5P328 crowfoot wrench (7/8") to loosen the fuel injection line nut at the nozzle end. 4. Use tool (B) to loosen the nut at the fuel injection line adapter end. Remove inner fuel injection lines (8). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 5. Remove bolts (9) that hold the rocker shaft assemblies to the cylinder head assembly.6. Remove rocker shaft assemblies (10). 7. Put identification marks on the push rods as to their location in the engine. Remove push rods (11). 8. Put identification marks on the bridges as to their location in the engine. Remove bridges (12) from the dowels on the cylinder head assembly.Install Rocker Shaft Assemblies And Push Rods
1. Put clean engine oil on the bridges and dowels. Install the original bridges in their respective locations. New bridges can be mixed.2. Install bridges (1) on the bridge dowels. While firmly pressing 0.5 to 4.5 kg (1 to 10 lb.) straight down on the top contact surface of the bridge, turn the adjusting screw clockwise until contact is made with the valve stem. Turn the screw an additional 20° to 30° (1/3 to 1/2 of 1 hex on nut). This will straighten the dowel in the guide and compensate for the slack in the threads. Hold the adjusting screw in this position, and tighten the locknut to a torque of 30 4 N m (22 3 lb.ft.). Install original push rods in their respective locations in the engine. New push rods can be mixed.3. Install push rods (2). 4. Put rocker shaft assemblies (3) in position on the cylinder head assembly.5. Put 5P3931 Anti-Seize Compound on the threads of the bolts that hold the rocker shaft assemblies in place. Tighten the bolts first to a torque of 270 25 N m (200 18 lb.ft.). Start with the bolt in the center of the rocker shaft assembly. Tighten the bolts again to a torque of 450 20 N m (330 15 lb.ft.). Tighten the bolts again by hand to a torque of 450 20 N m (330 15 lb.ft.).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (4). Tighten the fuel injection line adapter nuts (5) to a torque of 40 7 N m (30 5 lb.ft.) with tool (A).
Do not let the

Have questions with 19000-02821?





Group cross 19000-02821

Back to top