19000-02770 PUMP ASSY, INJECTI Denso Cross


Rating:
14
Buy PUMP ASSY, INJECTI 19000-02770 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 2J
Engine
2J
Serial start-end
7811--8201
Info
Injector Nozzle
093500-1810
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Governor assy, inj
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A4,MN
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
GOVERNOR ASSY, INJ
MN
01.004
TIMER ASSY, AUTOMA
01.004
TIMER ASSY, AUTOMA
SCZ
01.005
PUMP ASSY, FUEL FE
01.005
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-02770
PUMP ASSY, INJECTI
A4,MN
22100-41811-71 TOYOTA
001
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
002
[01]
GOVERNOR ASSY, INJ
MN
22310-20560-71 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
006
[01]
KEY, WOODRUFF
007
[01]
WASHER, SPRING
T3
008
[01]
NUT, TIMER ROUND
D16,L15
009
[01]
SHAFT, SPLINE
010
[04]
BOLT, W/WASHER
M6,L16
012
[01]
BOLT, W/WASHER
M8,L22
015
[01]
COVER, CONTROL RAC
016
[01]
COVER, PRIMING PUM
017
[01]
WIRE, OVER, INJECT
22175-46010 TOYOTA
020
[01]
TIMER ASSY, AUTOMA
SCZ

Include in ##:

19000-02770 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-02770 
22100-4181 
PUMP ASSY, INJECTI
1900002770 
22100-41811-71 
TOYOTA
PUMP ASSY, INJECTI




Information:

1. Disconnect hose assemblies (4) and (5) from elbow (6).2. Loosen the clamps that hold hose (1) in place, and move hose (1) away from elbow (6).3. Remove the bolt, lock and elbow (6) from the turbocharger.4. Loosen the clamps that hold elbow (7) in place, and move the elbow away from the turbocharger.5. Remove tube assemblies (8) and (9).6. Remove the clamp that holds pipe assembly (2) in position, and move the pipe assembly away from the turbocharger.7. Fasten a hoist to turbocharger (3). Remove the nuts that hold the turbocharger to the exhaust manifold, and remove the turbocharger. The weight of the turbocharger is 23 kg (51 lb.). The following steps are for installation of the turbocharger.8. Install the gasket between the turbocharger (3) and the exhaust manifold. Put 5P3931 Anti-Seize Compound on the threads of the bolts, and install the bolts and nuts that hold the turbocharger to the exhaust manifold. Tighten the bolts to a torque of 55 5 N m (41 4 lb.ft.).9. Make sure the gaskets are in position on tube assemblies (8) and (9), and install the tube assemblies.10. Put pipe assembly (2) in position on the turbocharger, and install the clamp that holds it.11. Put elbow (7) in position on the turbocharger, and install the clamps that hold it in place.12. Put elbow (6) in position in the turbocharger and hose (1). Tighten the clamps that hold the hose to the elbow.13. Install the lock and bolt to hold elbow (6) in position in the turbocharger.14. Connect hose assemblies (4) and (5) to elbow (6).Disassemble Turbocharger (S4A)
START BY:a. remove turbocharger (S4A) 1. Install the turbocharger on tool (A) as shown.2. Put alignment marks on three housings of the turbocharger for correct alignment during assembly. Loosen clamp (2), and remove the clamp and housing (1) from housing assembly (3). 3. Loosen clamp (4), and remove housing assembly (3) from housing (5). 4. Put the cartridge group in position in tool (B) as shown.
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
5. Use a 5S9566 Sliding T-Wrench and a universal socket (6) to remove the nut that holds the compressor wheel to the wheel assembly.6. Remove compressor wheel (7) and the shims from wheel assembly (8).7. Remove housing assembly (3) from wheel assembly (8). 8. Remove ring (9) and backplate (10) from wheel assembly (8). 9. Use tool (C), and remove snap ring (11) from housing assembly (3). 10. Remove insert (12) and sleeve (13) from housing assembly (3). 11. Remove ring (14) from sleeve (13). 12. Remove two screws (15) and deflector (16) from housing assembly (3). 13. Remove ring (18) and bearing assembly (17) from the housing assembly. 14. Remove sleeve (19) and ring (20) from the housing assembly. 15. Remove O-ring seal (23) from the housing assembly.16. Use tool (D), and remove snap ring (22) from the housing assembly.17. Remove bearing (21). Remove the snap

Have questions with 19000-02770?





Group cross 19000-02770

Back to top