19000-02673 PUMP ASSY, INJECTI Denso Cross


Rating:
59
Buy PUMP ASSY, INJECTI 19000-02673 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
01.002
BODY ASSY, INJECTI
A6,OLD
01.003
TIMER ASSY, AUTOMA
SA/2SP
01.004
PUMP ASSY, FUEL FE
KE
01.005
COUPLING ASSY

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-02673
PUMP ASSY, INJECTI
22100-77270 TOYOTA
001
[01]
BODY ASSY, INJECTI
A6,OLD
22120-77131 TOYOTA
002
[01]
GOVERNOR ASSY, COM
COMBINED
22320-77050 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
22510-77130 TOYOTA
004
[01]
TIMER ASSY, AUTOMA
SA/2SP
22610-77050 TOYOTA
005
[01]
COUPLING, INJECTIO
22632-66010 TOYOTA
006
[01]
COUPLING ASSY
22630-77051 TOYOTA
009
[01]
COVER, CONTROL RAC
22116-77020 TOYOTA
010
[01]
KEY, WOODRUFF
90099-13002 TOYOTA
011
[01]
NUT, TIMER ROUND
22611-77020 TOYOTA
012
[01]
WASHER, SPRING
ID12.2
94511-01200 TOYOTA
014
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
019
[04]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA

Include in ##:

19000-02673 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-02673 
22100-7727 
PUMP ASSY, INJECTI




Information:

2. Turn the crankshaft until two pistons are at bottom center.3. Remove nuts (1) and the bearing caps. Push the rods and pistons up until the rings are out of the cylinder liners. 4. Remove pistons (2) and connecting rods from the cylinder liners.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.Install Pistons And Connecting Rod Assemblies
1. Put clean engine oil on piston rings, connecting rod bearings and cylinder liners. Some engines use pistons which have the word "FRONT" stamped on the crown of the piston. These pistons also have a green color code on the bottom surface of the side relief directly under the word "FRONT". Make sure the word "FRONT" and the color code are toward the front of the engine when the piston is installed.2. Use tool (A), and install piston (1) and the connecting rod in the cylinder liner. Be sure the number on the tab groove side of the connecting rod is on the opposite side from the camshaft. Also, be sure the word "FRONT" on the crown of the piston is toward the front of the engine. 3. Install the bearing cap on the connecting rod with the number on the side of the bearing cap on the same side and same number as on the connecting rod.4. Put 2P2506 Thread Lubricant on the threads of the bolts. Install the nuts, and tighten them to a torque of 80 8 N m (60 6 lb.ft.). Put a mark on the nuts and cap, and tighten the nuts an extra 120°.5. Do Steps 1 through 4 for the remainder of the pistons.END BY:a. install oil pumpb. install cylinder head assemblyDisassemble And Assemble Pistons And Connecting Rod Assemblies
START BY:a. remove pistons and connecting rod assemblies 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See Use Of Piston Pin Bearing Removal And Installation Tools, Special Instructions, Form No. SMHS7295.5. Heat connecting rod (4) in an oven to a temperature of 177° to 260°C (350° to 500°F). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.7. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 50.830 0.008 mm (2.0012 .0003 in.).9. Check the

Have questions with 19000-02673?





Group cross 19000-02673

Back to top