19000-01783 PUMP ASSY, INJECTI Denso Cross


Rating:
48
Buy PUMP ASSY, INJECTI 19000-01783 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A4 COMBINED
01.002
BODY ASSY, INJECTI
A4
01.003
TIMER ASSY, AUTOMA
01.003
TIMER ASSY, AUTOMA
SCZ
01.004
PUMP ASSY, FUEL FE
KE22

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-01783
PUMP ASSY, INJECTI
A4 COMBINED
22100-48101 TOYOTA
001
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
22120-48110 TOYOTA
002
[01]
GOVERNOR ASSY, COM
22320-48040 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
22510-48032 TOYOTA
004
[01]
TIMER ASSY, AUTOMA
EXCLUDE
22610-48020 TOYOTA
006
[01]
KEY, WOODRUFF
90099-13002 TOYOTA
007
[01]
WASHER, SPRING
T3
22173-46010 TOYOTA
008
[01]
NUT, TIMER ROUND
D16,L15
22611-46010 TOYOTA
009
[01]
SHAFT, SPLINE
22174-47010 TOYOTA
010
[04]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA
012
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
015
[01]
COVER, CONTROL RAC
22116-46010 TOYOTA
018
[01]
BELLOWS ASSY, PNEU
22680-48062 TOYOTA
019
[01]
TUBE, RUBBER
90099-33044 TOYOTA
020
[01]
NUT, HEXAGON, W/ H
M22
90099-05137 TOYOTA
021
[01]
CLIP, CORD
90099-35023 TOYOTA

Include in ##:

19000-01783 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-01783 
22100-4810 
PUMP ASSY, INJECTI




Information:

2. Remove guide (5), spring (4) and plunger (3) from the cover. 3. Remove O-ring seal (6) from the back of the cover. 4. Remove inner rotor (7) and outer rotor (8) from the timing gear cover. 5. Measure the inside diameter of bearing (9). The inside diameter must be 71.22 0.05 mm (2.804 .002 in.). Remove bearing (9) only if a replacement is necessary. Remove shaft (10) if a replacement is necessary. Install Oil Pump And Relief Valve
1. Thoroughly clean all of the parts. Put oil on all of the pump parts. 2. If the bearing was removed from the timing gear cover, install a new bearing with tool (A). Make sure the bearing is installed with the joint in the position shown in the illustration. 3. If the shaft was removed from the timing gear cover, install the new shaft so dimension "X" from the top of the shaft to the counterbore in the cover is 36.14 0.25 mm (1.423 .010 in.). 4. Install inner rotor (1) and outer rotor (2) in the timing gear cover.5. Measure the clearance between the rotors with a feeler gauge. The clearance must be 0.05 to 0.20 mm (.002 to .008 in.). The maximum permissible clearance is 0.28 mm (.011 in.). Make a replacement of BOTH rotors if the clearance is not correct. The rotors can not be ordered separately.6. Put plunger (3), spring (4) and guide (5) in the cover. Use a 1-1/8 in. crowfoot wrench and torque wrench to tighten guide (5) to a torque of 41 7 N m (30 5 lb.ft.). A slide rule type torque computer, Form No. SEHS7150, is available to find the torque wrench dial reading for different extensions. 7. Install O-ring seal (6) on the cover and put the cover in position on the timing gear cover. Install the locks and bolts that hold the cover in place. 8. Check the oil pump and clearance with a feeler gauge. The end clearance must be 0.069 to 0.135 mm (.0027 to .0053 in.). If the clearance is not correct, make a replacement of BOTH rotors or the cover.end by:a) install timing gear cover and oil pump.

Have questions with 19000-01783?





Group cross 19000-01783

Back to top