19000-01720 PUMP ASSY, INJECTI Calibration Data


Rating:
20
Buy PUMP ASSY, INJECTI 19000-01720 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 2D
Engine
2D
Serial start-end
7706--8001
Info
Injector Nozzle
093500-1820
Injector nozzle: 0935001820

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A6,MZ
01.002
BODY ASSY, INJECTI
A6,OLD
01.003
TIMER ASSY, AUTOMA
SA/2SP
01.004
PUMP ASSY, FUEL FE
01.004
PUMP ASSY, FUEL FE
KE
01.005
COUPLING ASSY

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
A6,MZ
22100-40121-71 TOYOTA
001
[01]
BODY ASSY, INJECTI
A6,OLD
002
[01]
GOVERNOR ASSY, INJ
MZ
003
[01]
PUMP ASSY, FUEL FE
KE
004
[01]
TIMER ASSY, AUTOMA
SA/2SP
005
[01]
COUPLING, INJECTIO
006
[01]
COUPLING ASSY
009
[01]
COVER, CONTROL RAC
010
[01]
KEY, WOODRUFF
90099-13002 TOYOTA
011
[01]
COVER, PRIMING PUM
012
[01]
NUT, TIMER ROUND
013
[01]
WASHER, SPRING
ID12.2
016
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
018
[04]
BOLT, W/WASHER
M6,L16

Cross reference number



Part num
Firm num
Firm
Name
19000-01720 
 
PUMP ASSY, INJECTI
1900001720 
22100-40121-71 
TOYOTA
PUMP ASSY, INJECTI

Test Calibration Data:

1900001720 22100-40121-71




Information:


Do not overtighten the clamps.
(4) Diameter of shaft (new) ... 11.570 to 11.577 mm (.4555 to .4558 in)Bore in the bearing (new) ... 11.608 to 11.618 mm (.4570 to .4574 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(5) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(6) Install the compressor wheel (at room temperature) as follows:a. Put compressor wheel on the shaft.
Do not bend or add stress to the shaft when nut is loosened or tightened.
b. Remove nut from shaft and apply 6V1541 Quick Cure Primer on the threads of the shaft and nut followed by application of 9S3265 Retaining Compound.c. Tighten nut to ... 24.4 1.4 N m (144 4 lb in)(7) Thickness of each thrust ring ... 2.5463 0.0064 mm (.10025 .00025 in)(8) Bore in housing (new) ... 19.050 to 19.075 mm (.7500 to .7510 in)Outside diameter of the bearing (new) ... 18.936 to 18.948 mm (.7455 to .7460 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 70 15 N m (50 11 lb ft) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.

Have questions with 19000-01720?





Group cross 19000-01720

Back to top