19000-01622 PUMP ASSY, INJECTI Denso Cross


Rating:
29
Buy PUMP ASSY, INJECTI 19000-01622 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A4 COMBINED
01.002
BODY ASSY, INJECTI
A4
01.003
TIMER ASSY, AUTOMA
01.003
TIMER ASSY, AUTOMA
SCZ
01.004
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19000-01622
PUMP ASSY, INJECTI
A4 COMBINED
22100-48081 TOYOTA
001
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
22120-48110 TOYOTA
002
[01]
GOVERNOR ASSY, COM
22320-48080 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
22510-77130 TOYOTA
004
[01]
TIMER ASSY, AUTOMA
EXCLUDE
22610-48020 TOYOTA
006
[01]
KEY, WOODRUFF
90099-13002 TOYOTA
007
[01]
WASHER, SPRING
T3
22173-46010 TOYOTA
008
[01]
NUT, TIMER ROUND
D16,L15
22611-46010 TOYOTA
009
[01]
SHAFT, SPLINE
22174-47010 TOYOTA
010
[04]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA
012
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
015
[01]
COVER, CONTROL RAC
22116-46010 TOYOTA
018
[01]
BELLOWS ASSY, PNEU
22680-48062 TOYOTA
019
[01]
TUBE, RUBBER
90099-33044 TOYOTA
020
[01]
NUT, HEXAGON, W/ H
M22
90099-05137 TOYOTA
021
[01]
CLIP, CORD
90099-35023 TOYOTA

Include in ##:

19000-01622 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
19000-01622 
22100-4808 
PUMP ASSY, INJECTI




Information:

Illustrations show fuel injection pump housing and governor removed from engine. Service work can be done with it installed on engine.1. Remove air bleed lines (2). 2. Remove bolts (1), flange (3), the flange assembly and the gaskets.3. Remove the bolts and the cover. 4. Remove bolts (5), solenoid (4) and the gasket.5. Remove two bolts (7) and fuel ratio control (6).6. Remove the shutoff housing from the cover. 7. Remove the bolts, lever (10) and shaft (8).8. Remove the bolts, lever (9) and shaft (11).9. Remove seal (12) from the shutoff housing. Install Shutoff Housing
1. Put 5S1454 Sealing Compound on the outside diameter of the seal and install the seal (1) with tooling (A) in the shutoff housing with the lip toward the outside. The outer face of the seal must be 1.0 mm (.039 in.) below the surface of the housing. Remove the extra sealing compound from the housing and the seal after installation. 2. Put shaft (5) in position in housing (4).3. Install lever (6) and the bolts. 4. Install shaft (2), lever (3) and the bolts. Make an alignment of the notch in shaft (2) with lever (3). 5. Put cover (7) in position on shutoff housing assembly (8) and install the bolts.6. Put fuel ratio control (10) in position and install the bolts. 7. Install the gasket, solenoid (9) and bolts on the cover.8. Put the cover in position and install the bolts.9. Install the gasket, flange assembly, gasket, flange (11) and the bolts.10. Connect air bleed lines (12).

Have questions with 19000-01622?





Group cross 19000-01622

Back to top