Rating:
Information pump assy, injecti Denso
Product
Fuel Injection Pump
Vehicle engine
CRESSIDA 2L
Engine
2L
Serial start-end
8404--9912
Info
Injector Nozzle
093500-2860
Manufacture:
22100-54450 TOYOTA
Dim 1
3.2-3.4
Dim 2
5.5-5.7
Dim 3
0.44-0.54
Dim 4
Dim 5
Dim 6
Information
Injector nozzle:
0935002860
KIT List:
Part name
Kit1
Kit2
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09600-01900
PUMP ASSY, INJECTI
22100-54450
TOYOTA
Include in ##:
09600-01900
as PUMP ASSY, INJECTI
Cross reference number
Part num
Firm num
Firm
Name
09600-01900
22100-5445
PUMP ASSY, INJECTI
0960001900
22100-54450
TOYOTA
PUMP ASSY, INJECTI
Information:
If there is clearance available, it is recommended that the oil pan be removed prior to removing the rear seal carrier. A new oil pan gasket must be installed after the rear seal carrier has been installed.1. Loosen oil pan mounting bolts (2). Carefully lower the oil pan away from the cylinder block.2. Remove eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block. Using a screwdriver, carefully pry the rear seal carrier off of the two dowels in the cylinder block. The following steps are for the installation of the rear seal carrier.
1U8846 Gasket Maker is used on the joint face of the rear seal carrier. Do not allow the gasket maker to get into the oil passage in the cylinder block mounting face.
3. Prepare rear seal carrier (3) for installation as follows: a. Clean the joint face of the rear seal carrier with 8T9011 Component Cleaner.b. Apply 6V1541 Quick Cure Primer to the joint face of the rear seal carrier. Allow the primer to air dry three to five minutes.c. Apply 1U8846 Gasket Maker to the joint face of the rear seal carrier. Spread the gasket maker uniformly. The rear seal carrier must be installed within ten minutes after application of the gasket maker.4. Put rear seal carrier (3) in position on the dowels in the rear of the cylinder block. If necessary, use a soft faced hammer to position the rear seal carrier against the cylinder block.5. Apply 9S3263 Thread Lock on the threads of eight bolts (1). Install eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block.6. Check the condition of the oil pan gasket. If the gasket is not damaged, raise the oil pan into position, and tighten oil pan mounting bolts (2). If the gasket is damaged, remove the oil pan, and replace the gasket. See the topic "Remove & Install Oil Pan" in this module.End By:a. install flywheel housing
1U8846 Gasket Maker is used on the joint face of the rear seal carrier. Do not allow the gasket maker to get into the oil passage in the cylinder block mounting face.
3. Prepare rear seal carrier (3) for installation as follows: a. Clean the joint face of the rear seal carrier with 8T9011 Component Cleaner.b. Apply 6V1541 Quick Cure Primer to the joint face of the rear seal carrier. Allow the primer to air dry three to five minutes.c. Apply 1U8846 Gasket Maker to the joint face of the rear seal carrier. Spread the gasket maker uniformly. The rear seal carrier must be installed within ten minutes after application of the gasket maker.4. Put rear seal carrier (3) in position on the dowels in the rear of the cylinder block. If necessary, use a soft faced hammer to position the rear seal carrier against the cylinder block.5. Apply 9S3263 Thread Lock on the threads of eight bolts (1). Install eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block.6. Check the condition of the oil pan gasket. If the gasket is not damaged, raise the oil pan into position, and tighten oil pan mounting bolts (2). If the gasket is damaged, remove the oil pan, and replace the gasket. See the topic "Remove & Install Oil Pan" in this module.End By:a. install flywheel housing