Rating:
Information pump assy, injecti Denso
Product
Fuel Injection Pump
Vehicle engine
GALANT 4D65T
Engine
4D65T
Serial start-end
8403--8512
Info
Injector Nozzle
093500-2620
Manufacture:
MD077256 MITSUBISHI
Dim 1
3.2-3.4
Dim 2
5.8-6.0
Dim 3
0.6-0.8
Dim 4
Dim 5
Dim 6
Information
Injector nozzle:
0935002620
KIT List:
Part name
Kit1
Kit2
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09600-01610
PUMP ASSY, INJECTI
VE4,M-M
MD077256
MITSUBISHI
Include in ##:
09600-01610
as PUMP ASSY, INJECTI
Cross reference number
Part num
Firm num
Firm
Name
09600-01610
MD077256
PUMP ASSY, INJECTI
0960001610
MD077256
MITSUBISHI
PUMP ASSY, INJECTI
Information:
Crater. The piston is a symmetrical piston with an "on center" crater. Thoroughly lubricate piston group 360° in zone (A) with clean engine oil prior to inserting into the block group.(2) Top piston ring. Install ring with side marked "UP-1" toward top of piston (red color stripe to right of ring end gap).Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.625 0.190 mm (.0250 .0075 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)Minimum depth of groove in piston for top ring (new) ... 5.43 mm (.214 in)(3) Intermediate piston ring. Install ring with side marked "UP-2" toward top of piston (green color stripe to right of ring end gap).Width of groove in piston for intermediate ring (new) ... 3.061 0.013 mm (.1032 .0005 in)Minimum depth of groove in piston for intermediate ring (new) ... 5.43 mm (.214 in)Thickness of intermediate ring (new) ... 2.990 0.010 mm (.1177 .0004 in)Clearance between groove and intermediate ring (new) ... 0.048 to 0.094 mm (.0002 to .0037 in)Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.625 0.125 mm (.0250 .0050 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)(4) Oil regulating piston ring. Oil ring spring ends to be assembled 180° from ring end gap (orange colored portion of spring must be visible at ring end gap).Width of groove in piston for oil ring ... 4.033 0.013 mm (.1588 .0005 in)Minimum depth of groove in piston for oil ring (new) ... 3.727 mm (.1467 in)Thickness of oil ring (new) ... 3.987 0.013 mm (.1570 .0005 in)Clearance between groove and oil ring (new) ... 0.020 to 0.072 mm (.0008 to .0028 in)Clearance between ends of piston ring when installed in a cylinder liner with a bore size of 125.000 mm (4.9213 in) ... 0.44 0.15 mm (.017 .006 in)Increase in clearance between ends of piston ring for each 0.03 mm (.001 in) increase in cylinder liner bore size ... 0.09 mm (.004 in)After piston rings have been installed, rotate rings so the end gaps are 120° apart.(5) Crown assembly.(6) Piston pin bore diameter in piston skirt ... 51.15 0.15 mm (2.014 .006 in)Thoroughly lubricate piston pin with clean engine oil prior to inserting into piston group and rod assembly.(7) Piston skirt.