09450-07460 PUMP ASSY, INJECTI Calibration Data


Rating:
4
Buy PUMP ASSY, INJECTI 09450-07460 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL S3L-61SP
Engine
S3L-61SP
Serial start-end
9810--9904
Info
Injector Nozzle
093500-3840
Injector nozzle: 0935003840

Components :

00.001
PUMP ASSY, INJECTI
PFR3M

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09450-07460
PUMP ASSY, INJECTI
PFR3M
005
[01]
HOUSING SUB-ASSY,
006
[03]
HOLDER, DELIVERY V
007
[03]
SPRING, DELIVERY V
008
[03]
GASKET, DELIVERY V
ID 9
009
[03]
VALVE SUB-ASSY, IN
MK:250
010
[03]
ELEMENT SUB-ASSY,
MARK5550
011
[03]
SLEEVE, PLUNGER CO
012
[03]
SEAT, SPRING, UPR
013
[03]
SPRING, PUMP PLUNG
L36.3
014
[03]
TAPPET SUB-ASSY,IN
014-001
[03]
TAPPET, INJECTION
014-002
[03]
ROLLER, FEED PUMP
014-003
[03]
PIN, INJECTION PUM
015
[03]
PIN, INJECTION PUM
016
[01]
RACK ASSY, CONTROL
017
[03]
SEAT, SPRING, LWR
018
[01]
PLATE
019
[3C]
PLATE, TAPPET ADJU
T0.6
019
[3C]
PLATE, TAPPET ADJU
T0.2
019
[3C]
PLATE, TAPPET ADJU
T0.3
019
[3C]
PLATE, TAPPET ADJU
T0.4
019
[3C]
PLATE, TAPPET ADJU
T0.5
019
[3C]
PLATE, TAPPET ADJU
T0.25
019
[3C]
PLATE, TAPPET ADJU
T0.35
019
[3C]
PLATE, TAPPET ADJU
T0.45
019
[3C]
PLATE, TAPPET ADJU
T0.55
019
[3C]
PLATE, TAPPET ADJU
T0.65
020
[01]
WASHER, COPPER PLA
T1,ID8.2
021
[01]
SCREW, AIR BLEEDER
022
[01]
SCREW, HOLLOW
023
[02]
PLATE, ADJUSTING
024
[02]
BOLT, WASHER HEAD
M6,L8
027
[03]
O-RING
ID14.8 -0501
027
[03]
O-RING
ID14.8 0502-

Include in ##:

09450-07460 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09450-07460 
 
PUMP ASSY, INJECTI

Test Calibration Data:

0945007460 31B65-04010




Information:

3. Remove cylinder liners (1) with tooling (A).Install Cylinder Liners
1. Clean the cylinder liners (3) and the liner bores in the cylinder block.2. Install the cylinder liners in the block without the O-ring seals or filler bands.3. Check the cylinder liner projection as follows: a) Install the S1589 Bolts (2) and 1S379 Washers of tooling (B) on the cylinder block next to each liner. Tighten the bolts evenly, in four steps: 10 lb. ft. (14 N m), 25 lb. ft. (35 N m), 50 lb. ft. (70 N m) and 70 lb. ft. (95 N m).b) Put adapter plate on top of the liner and install the remainder of tooling (B). Tighten the 1D4595 Bolts (1) evenly in four steps: 5 lb. ft. (7 N m), 15 lb. ft. (20 N m), 25 lb. ft. (35 N m) and 50 lb. ft. (70 N m).c) Check to be sure the distance from the bottom edge of the crossbar to the top of the cylinder block is the same on both sides of the liner.d) Check the cylinder liner projection with tool group (C) at four locations around the liner.e) Liner projection must be .0013 to .0069 in. (0.033 to 0.175 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurements between liners next to each other must not be different by more than .002 in. (0.05 mm). The maximum permissible difference between average projection of all cylinder liners under one cylinder head is .004 in. (0.10 mm). If the liner is turned in the bore, it can make a difference in the liner projection.4. If the liner projection is not .0013 to .0069 in. (0.033 to 0.175 mm), check the thickness of the following parts: spacer plate, spacer plate gasket and cylinder liner flange. The thickness of the spacer plate must be .3925 .0010 in. (9.970 0.025 mm). The thickness of the spacer plate gasket must be .0082 .0010 in. (0.208 0.025 mm). The thickness of the cylinder liner flange must be .4048 .0008 in. (10.282 0.020 mm). If the liner projection changes from point to point around the liner, turn the liner to a new position in the bore. If the liner projection is still not to specifications, move the liner to a different bore.5. When the cylinder projection is correct, put a mark on the liner and block so the liner can be installed in the same position from which it was removed. Cylinder liner projection can be adjusted by the removal of material from (machining) the contact face of the cylinder block with the use of the 8S3140 Cylinder Block Counterboring Tool Arrangement. Machine to a minimum depth of .030 in. (0.76 mm) and to a maximum depth of .045 in. (1.14 mm). The instructions for the use of the tool group are in Special Instruction Form No. FM055228. Shims are available for the adjustment of the liner projection. See

Have questions with 09450-07460?





Group cross 09450-07460

Back to top