09450-07290 PUMP ASSY, INJECTI Calibration Data


Rating:
1
Buy PUMP ASSY, INJECTI 09450-07290 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL S4L2-61SDH
Engine
S4L2-61SDH
Serial start-end
9708-
Info
Injector Nozzle
093500-3840
Injector nozzle: 0935003840

Components :

00.001
PUMP ASSY, INJECTI
PFR4M

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09450-07290
PUMP ASSY, INJECTI
PFR4M
005
[01]
HOUSING SUB-ASSY,
006
[04]
HOLDER, DELIVERY V
007
[04]
SPRING, DELIVERY V
008
[04]
GASKET, DELIVERY V
009
[04]
VALVE SUB-ASSY, IN
010
[04]
ELEMENT SUB-ASSY,
011
[04]
SLEEVE, PLUNGER CO
012
[04]
SEAT, SPRING, UPR
013
[04]
SPRING, PUMP PLUNG
014
[04]
TAPPET SUB-ASSY,IN
014-001
[04]
TAPPET, INJECTION
014-002
[04]
ROLLER, FEED PUMP
014-003
[04]
PIN, INJECTION PUM
015
[04]
PIN, INJECTION PUM
016
[01]
RACK ASSY, CONTROL
017
[04]
SEAT, SPRING, LWR
018
[02]
PLATE
019
[4C]
PLATE, TAPPET ADJU
T0.6
019
[4C]
PLATE, TAPPET ADJU
T0.2
019
[4C]
PLATE, TAPPET ADJU
T0.3
019
[4C]
PLATE, TAPPET ADJU
T0.4
019
[4C]
PLATE, TAPPET ADJU
T0.5
019
[4C]
PLATE, TAPPET ADJU
T0.25
019
[4C]
PLATE, TAPPET ADJU
T0.35
019
[4C]
PLATE, TAPPET ADJU
T0.45
019
[4C]
PLATE, TAPPET ADJU
T0.55
019
[4C]
PLATE, TAPPET ADJU
T0.65
020
[01]
WASHER, COPPER PLA
T1
021
[01]
SCREW, AIR BLEEDER
022
[01]
SCREW, HOLLOW
M14,L26
023
[03]
PLATE, ADJUSTING
024
[03]
BOLT, WASHER HEAD
M6,L8
025
[04]
O-RING
ID14.8 -0501
025
[04]
O-RING
ID14.8 0502-

Include in ##:

09450-07290 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09450-07290 
 
PUMP ASSY, INJECTI

Test Calibration Data:

0945007290 31A65-03060




Information:

Engine Crankshaft Will Not Turn Recommended Procedure1. Low or No Battery Voltage ... Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the ELECTRICAL SYSTEM of the Testing and Adjusting section of this Service Manual.2. Bad Switch, Bad Wiring or Connection in Switch Circuit ... With ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used).3. Bad Cable or Connection; Battery to Starter... With ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at

Have questions with 09450-07290?





Group cross 09450-07290

Back to top