09450-06100 PUMP ASSY, INJECTI Calibration Data


Rating:
63
Buy PUMP ASSY, INJECTI 09450-06100 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL K3E-32
Engine
K3E-32
Serial start-end
9110--9112
Info
Injector Nozzle
093500-1660
Injector nozzle: 0935001660

Components :

00.001
PUMP ASSY, INJECTI
PFR3M

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09450-06100
PUMP ASSY, INJECTI
PFR3M
005
[01]
HOUSING SUB-ASSY,
006
[03]
HOLDER, DELIVERY V
007
[03]
SPRING, DELIVERY V
008
[03]
GASKET, DELIVERY V
009
[03]
VALVE SUB-ASSY, IN
MK: -
010
[03]
ELEMENT SUB-ASSY,
MK:2400
011
[03]
SLEEVE, PLUNGER CO
012
[03]
SEAT, SPRING, UPR
013
[03]
SPRING, PUMP PLUNG
014
[03]
TAPPET SUB-ASSY,IN
014-001
[03]
TAPPET, INJECTION
014-002
[03]
ROLLER, FEED PUMP
014-003
[03]
PIN, INJECTION PUM
015
[03]
PIN, INJECTION PUM
016
[01]
RACK ASSY, CONTROL
017
[03]
SEAT, SPRING, LWR
018
[01]
PLATE
019
[3C]
PLATE, TAPPET ADJU
T0.6
019
[3C]
PLATE, TAPPET ADJU
T0.2
019
[3C]
PLATE, TAPPET ADJU
T0.3
019
[3C]
PLATE, TAPPET ADJU
T0.4
019
[3C]
PLATE, TAPPET ADJU
T0.5
019
[3C]
PLATE, TAPPET ADJU
T0.25
019
[3C]
PLATE, TAPPET ADJU
T0.35
019
[3C]
PLATE, TAPPET ADJU
T0.45
019
[3C]
PLATE, TAPPET ADJU
T0.55
019
[3C]
PLATE, TAPPET ADJU
T0.65
020
[01]
WASHER, FUEL PIPE
-9705
020
[01]
WASHER, COPPER PLA
9706-
021
[01]
SCREW, AIR BLEEDER
022
[01]
SCREW, HOLLOW
023
[02]
PLATE, ADJUSTING
024
[02]
BOLT, WASHER HEAD
025
[01]
SPRING, DIAPHRAGM
026
[01]
SPRING, DIAPHRAGM
027
[03]
O-RING
ID14.8
028
[01]
E-RING
029
[01]
E-RING
032
[1C]
STOPPER
1,L16.9
032
[1C]
STOPPER
2,L16.8
032
[1C]
STOPPER
3,L16.7
032
[1C]
STOPPER
4,L16.6
032
[1C]
STOPPER
5,L16.5
033
[1C]
STOPPER
58,L2.1
033
[1C]
STOPPER
59,L2.2
033
[1C]
STOPPER
60,L2.3
033
[1C]
STOPPER
61,L2.4
033
[1C]
STOPPER
62,L2.5
033
[1C]
STOPPER
63,L2.6
033
[1C]
STOPPER
64,L2.7
033
[1C]
STOPPER
65,L2.8
033
[1C]
STOPPER
66,L2.9
033
[1C]
STOPPER
67,L3.0
033
[1C]
STOPPER
68,L3.1
033
[1C]
STOPPER
69,L3.2
033
[1C]
STOPPER
70,L3.3
033
[1C]
STOPPER
71,L3.4
033
[1C]
STOPPER
72,L3.5

Include in ##:

09450-06100 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09450-06100 
 
PUMP ASSY, INJECTI

Test Calibration Data:

0945006100 30A6504200




Information:

Introduction
This Special Instruction contains the necessary procedure in order to install unit injectors for 3114, 3116, and 3126 MUI engines.Removal and Installation Procedure
Note: To avoid damage to the unit injector during removal of the unit injector from the cylinder head, refer to the Service Manual for the removal procedure of the unit injector.Use the latest process for servicing the unit injector sleeves in the cylinder head before you install replacement unit injectors. Refer to the Service Manual and other service news articles in order to find the latest service information, including new tools and procedures.Before a new unit injector or a remanufactured unit injector is installed into an engine, take adequate precautions in order to clean the internal fuel lines and the unit injector sleeve. Also, install a new Caterpillar high efficiency fuel filter.Lubricate the injector rack bar with clean diesel fuel or 1U-8265 Penetrating Oil .
Illustration 1 g02144296
Incorrect testing procedure for the tappet springDo not depress the tappet spring. Refer to Illustration 1. Do not force the injector rack bar in and out since this action may damage the internal parts of the unit injector. A tight rack on a unit injector that is not installed in the engine is not an indication of a faulty unit injector. Forcing the injector rack bar in and out may cause the unit injector to become damaged. Forcing the injector rack bar in and out may possibly void all the warranty.Do not test the unit injectors prior to engine installation. The unit injectors are tested 100% at the factory and Pop Testing may contaminate the unit injector.Before you install the unit injector, apply clean engine oil on the O-ring seals for ease of installation.Install the unit injector according to the procedure in the Service Manual by using 173-1530 Injector Seating Tool . Tighten the unit injector clamp retaining bolt to a torque of 12 3 N m (9 2 lb ft).Verify the following parameters and settings according to the procedures in the Service Manual: unit injector synchronization, fuel setting, fuel timing and valve lash. Adjust the parameters and settings in order to meet specifications only.

Have questions with 09450-06100?





Group cross 09450-06100

Back to top