09450-02530 PUMP ASSY, INJECTI Calibration Data


Rating:
78
Buy PUMP ASSY, INJECTI 09450-02530 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL E40
Engine
E40
Serial start-end
8301-
Info
Injector Nozzle
093500-2330
Injector nozzle: 0935002330

Components :

00.001
PUMP ASSY, INJECTI
PFR1M

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
PFR1M
14541-51012 KUBOTA
001
[01]
HOUSING SUB-ASSY,
-9710
14287-51081 KUBOTA
001
[01]
HOUSING SUB-ASSY,
9711-
002
[01]
HOLDER, DELIVERY V
-9004
15601-51221 KUBOTA
002
[01]
HOLDER, DELIVERY V
9005-
003
[01]
SPRING, DELIVERY V
15221-51231 KUBOTA
004
[01]
GASKET, DELIVERY V
-9005
15221-51241 KUBOTA
004
[01]
GASKET, DELIVERY V
9005-
11420-51241 KUBOTA
005
[01]
VALVE SUB-ASSY, IN
MK:-
15271-51031 KUBOTA
006
[01]
ELEMENT SUB-ASSY,
MK:1360
15271-51051 KUBOTA
008
[01]
SEAT, SPRING, UPR
15221-51271 KUBOTA
009
[01]
SPRING, PUMP PLUNG
15221-51281 KUBOTA
010
[01]
SLEEVE, PLUNGER CO
15221-51382 KUBOTA
011
[01]
TAPPET SUB-ASSY,IN
15221-51071 KUBOTA
011-001
[01]
TAPPET, INJECTION
15021-51990 KUBOTA
011-002
[01]
ROLLER, FEED PUMP
15109-52931 KUBOTA
011-003
[01]
PIN, INJECTION PUM
15021-51970 KUBOTA
012
[01]
RACK ASSY, CONTROL
14911-51061 KUBOTA
015
[01]
SCREW, HOLLOW
M10
14911-51321 KUBOTA
016
[02]
WASHER, AIR BLEEDE
T1.6
15221-96651 KUBOTA
017
[01]
PIN, INJECTION PUM
-9702
15221-51251 KUBOTA
017
[01]
PIN, INJECTION PUM
9702-
018
[01]
SEAT, SPRING, LWR
15021-51291 KUBOTA
019
[01]
RING, SNAP
ID27.6
020
[01]
O-RING
ID14.8 -0501
14611-51201 KUBOTA
020
[01]
O-RING
ID14.8 0502-
022
[C]
PLATE, TAPPET ADJU
T0.6
14109-51301 KUBOTA
022
[C]
PLATE, TAPPET ADJU
T0.2
022
[C]
PLATE, TAPPET ADJU
T0.3
022
[C]
PLATE, TAPPET ADJU
T0.4
15221-51491 KUBOTA
022
[C]
PLATE, TAPPET ADJU
T0.5
022
[C]
PLATE, TAPPET ADJU
T0.25
022
[C]
PLATE, TAPPET ADJU
T0.35
022
[C]
PLATE, TAPPET ADJU
T0.45
022
[C]
PLATE, TAPPET ADJU
T0.55
022
[C]
PLATE, TAPPET ADJU
T0.65

Cross reference number



Part num
Firm num
Firm
Name
09450-02530 
 
PUMP ASSY, INJECTI
0945002530 
14541-51012 
KUBOTA
PUMP ASSY, INJECTI

Test Calibration Data:

0945002530 14541-51011




Information:

System Operation
The SLC 5/04 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: Input devices, Output devices, Wiring and The controller.The green "RUN" LED is illuminated. The processor is in the "RUN" mode.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.The amber "FORCE" LED is illuminated. The forces are enabled.The amber "FORCE" LED is not illuminated. No forces are present or no forces are enabled.
Illustration 1 g00563544
Diagram of the LED indicators
Illustration 2 g00562937
Functional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Clear the fault.
Place the switch in the PROG position.
Place the switch in the RUN position.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Proceed to 3.
Cycle the power.
Secure power to the PLC.
Energize the PLC.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Refer to Maintenance Procedure, "Processor - Replace".

Have questions with 09450-02530?





Group cross 09450-02530

Back to top