09450-01030 PUMP ASSY, INJECTI Denso Cross


Rating:
70
Buy PUMP ASSY, INJECTI 09450-01030 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
Construction machine KE135-11C
Engine
KE135-11C
Serial start-end
7706--8201
Info
Injector Nozzle
093500-1680
Injector nozzle: 0935001680

Components :

00.001
PUMP ASSY, INJECTI
PFR2K

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
PFR2K
005
[01]
HOUSING SUB-ASSY,
006
[02]
HOLDER, DELIVERY V
007
[02]
SPRING, DELIVERY V
008
[02]
GASKET, DELIVERY V
009
[02]
VALVE SUB-ASSY, IN
MK: -
010
[02]
ELEMENT SUB-ASSY,
011
[02]
SLEEVE, PLUNGER CO
012
[02]
SEAT, SPRING, UPR
013
[02]
SPRING, PUMP PLUNG
014
[02]
TAPPET SUB-ASSY,IN
014-001
[02]
TAPPET, INJECTION
014-002
[02]
PIN, INJECTION PUM
014-003
[02]
ROLLER, FEED PUMP
015
[02]
PIN, INJECTION PUM
016
[01]
RACK ASSY, CONTROL
017
[02]
SEAT, SPRING, LWR
018
[01]
PLATE
019
[02]
O-RING
ID14.8 -0501
019
[02]
O-RING
ID14.8 0502-
020
[1C]
PLATE, TAPPET ADJU
T0.6
020
[1C]
PLATE, TAPPET ADJU
T0.2
020
[1C]
PLATE, TAPPET ADJU
T0.3
020
[1C]
PLATE, TAPPET ADJU
T0.4
020
[1C]
PLATE, TAPPET ADJU
T0.5
020
[1C]
PLATE, TAPPET ADJU
T0.25
020
[1C]
PLATE, TAPPET ADJU
T0.35
020
[1C]
PLATE, TAPPET ADJU
T0.55
020
[1C]
PLATE, TAPPET ADJU
T0.65
021
[01]
WASHER, FUEL PIPE
-9705
021
[01]
WASHER, COPPER PLA
T1 9706-
022
[01]
SCREW, AIR BLEEDER
023
[01]
SCREW, HOLLOW
024
[01]
BOLT, WASHER HEAD
M6,L8
025
[01]
PLATE, ADJUSTING
026
[01]
SPRING, DIAPHRAGM
027
[01]
E-RING
028
[1C]
STOPPER
11,L4.1
028
[1C]
STOPPER
12,L4.4
028
[1C]
STOPPER
13,L4.7
028
[1C]
STOPPER
14,L5.0
028
[1C]
STOPPER
15,L5.3
028
[1C]
STOPPER
16,L5.6
028
[1C]
STOPPER
17,L5.9
028
[1C]
STOPPER
18,L6.2

Cross reference number



Part num
Firm num
Firm
Name
09450-01030 
 
PUMP ASSY, INJECTI




Information:

Introduction
This Special Instruction gives detailed instructions on the disassembly and assembly of the 144-0835 Unit Injector Hydraulic Pump . The 144-0835 Unit Injector Hydraulic Pump was not previously serviceable. The pump will have a kit that will contain serviceable parts. The rear bearing and the bearing kits for the pump will be serviceable on an individual basis.Note: This instruction should also be used when you are servicing the former 134-9405 Unit Injector Hydraulic Pump .Serviceable Parts
154-6732 Fuel Injection Pump Kit
Control Piston
Shaft
Yoke
Seal Kit
Front Bearing
Rotating Group
154-6734 Bearing
154-6735 Bearing Kit Required Tools
Contact the Caterpillar Dealer for the dimensions and specifications that are needed in order to fabricate the tools.
Illustration 1 g00295533
FT-2606 Yoke Fixture
Illustration 2 g00295534
Two FT-2607 Bearing Installation Tools
Illustration 3 g00295535
FT-2608 Bearing Installation Tool
Illustration 4 g00295536
FT-2609 Valve Block Positioner
Illustration 5 g00295537
FT-2610 Driver Tube
Illustration 6 g00295538
FT-2611 Bearing Support
Illustration 7 g00295539
FT-2612 Bearing Removal Tool Disassembly Of The 144-0835 Unit Injector Hydraulic Pump
Start by removing the 128-3552 Unit Injection Hydraulic Pump and Mounting Gp from the engine.Reference: Consult the Service Manual, SENR1063 for additional information.Note: Do not disconnect the fuel transfer pump from the 128-3552 Unit Injection Hydraulic Pump and Mounting Gp before servicing. The coupling between the two pumps will be used later.
Illustration 8 g00295292
(1) Fuel Transfer Pump. (2) Bolts.
Remove the four bolts (2) from the fuel transfer pump (1). Remove the fuel transfer pump (1) .
Illustration 9 g00295294
(3) Compensator. (4) Bolt.
Remove the four bolts (4) from the compensator (3). Remove the compensator (3) and the adapter. Do not adjust the compensator (3) .
Illustration 10 g00295295

Have questions with 09450-01030?





Group cross 09450-01030

Back to top