Rating:
Information pump assy, supply Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$3,380.31
19 Sep 2024
0.1102[0.05] pounds
CN: JianRuanMaoY0101
WEIJIIAUS 8-98013910-0 Fuel Injection Pump 898013910 8-98013910-1 8-094000-0560 094000-0565 Compatible with Isuzu 4HK1 6HK1 6WG1 4BG1
WEIJIIAUS ⭐ Run at high speed to ensure a stable fuel supply. || ⭐ Low power consumption, reducing power consumption and fuel waste. || ⭐ High pressure output ensures that the fuel reaches every part of the engine. || ⭐ Reliable pump body material ensures that the pump body will not be deformed or damaged. || ⭐ Accurate fuel injection improves fuel efficiency and engine performance.
WEIJIIAUS ⭐ Run at high speed to ensure a stable fuel supply. || ⭐ Low power consumption, reducing power consumption and fuel waste. || ⭐ High pressure output ensures that the fuel reaches every part of the engine. || ⭐ Reliable pump body material ensures that the pump body will not be deformed or damaged. || ⭐ Accurate fuel injection improves fuel efficiency and engine performance.
$1,234.25
19 Sep 2024
CN: CAR REFINE
8-98013910-5 094000-0565 Fuel Injection Pump Type Fits for Isuzu Diesel Engine 6WG1
Podafu Part Name: Fuel Injection Pump || Part Number: 8-98013910-5 || Applicable: Compatible with Isuzu Diesel Engine 6WG1 || The fuel injection pump has a long service life, low maintenance frequency, and high reliability || Before purchasing, please carefully check if the product is suitable for your vehicle by reviewing the part number and photos.
Podafu Part Name: Fuel Injection Pump || Part Number: 8-98013910-5 || Applicable: Compatible with Isuzu Diesel Engine 6WG1 || The fuel injection pump has a long service life, low maintenance frequency, and high reliability || Before purchasing, please carefully check if the product is suitable for your vehicle by reviewing the part number and photos.
$1,366.99
19 Sep 2024
CN: CAR REFINE
Fuel Injection Pump for Isuzu Engine 6UZ1 094000-0565 0940000565
Podafu Part Number：0940000565 || Application：For Isuzu Engine 6UZ1
Podafu Part Number：0940000565 || Application：For Isuzu Engine 6UZ1
You can buy:
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09400-00565
8-98013910
PUMP ASSY, SUPPLY
Information:
1. Install the turbocharger on Tool (A).2. Put alignment marks on the two housings and cartridge assembly of the turbocharger for correct alignment during assembly.3. Loosen clamp (3), and remove compressor housing (4) from cartridge assembly (2).4. Loosen the remaining clamp, and remove cartridge assembly (2) from turbine housing (1).
Typical Example5. Put the cartridge group (shown in the illustration) with nut (16) up in Tool (B). Use a 5S9566 Sliding T-Wrench and a universal socket to remove nut (16) that holds the compressor wheel (15) to the wheel assembly (19).6. Remove compressor wheel (15) and housing assembly (6) from wheel assembly (19). Remove piston ring (13) from the wheel assembly.7. Use Tool (C), and remove snap ring (5) from housing assembly (6). Remove insert (14) and sleeve (18) from the housing assembly. Remove seal (22) from insert (14). Remove ring (20) from sleeve (18).8. Remove oil deflector (23), thrust ring (21), bearing assembly (7), spacer sleeve (24) and thrust ring (8) from housing assembly (6).9. Use Tool (D), and remove snap ring (9) from the housing assembly. Remove bearing (25). Remove snap ring (10) with Tool (D).10. Use Tool (D), and remove snap ring (12) from the housing assembly. Remove bearing (26). Remove snap ring (11) with Tool (D).11. Check all the parts of the turbocharger for damage. If any parts are damaged, use new parts for replacement. See Special Instruction Form No. SMHS6854 for turbocharger reconditioning. Also, see Guidelines For Reusable Parts, Form No. SEBF8018. The following steps are for assembly of the turbocharger.12. Make sure that all the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, put clean engine oil into the oil inlet of the turbocharger.
Make sure the snap rings that hold bearings (25) and (26) in housing assembly (6) are installed with the round edge of the outside diameter toward the bearing.
13. Install snap ring (11) with Tool (D). Install bearing (26). Install snap ring (12) with Tool (D).14. Install snap ring (10) with Tool (D). Install bearing (25). Install snap ring (9) with Tool (D).15. Put wheel assembly (19) in position on Tool (B) with the threaded portion end up.
Typical Example5. Put the cartridge group (shown in the illustration) with nut (16) up in Tool (B). Use a 5S9566 Sliding T-Wrench and a universal socket to remove nut (16) that holds the compressor wheel (15) to the wheel assembly (19).6. Remove compressor wheel (15) and housing assembly (6) from wheel assembly (19). Remove piston ring (13) from the wheel assembly.7. Use Tool (C), and remove snap ring (5) from housing assembly (6). Remove insert (14) and sleeve (18) from the housing assembly. Remove seal (22) from insert (14). Remove ring (20) from sleeve (18).8. Remove oil deflector (23), thrust ring (21), bearing assembly (7), spacer sleeve (24) and thrust ring (8) from housing assembly (6).9. Use Tool (D), and remove snap ring (9) from the housing assembly. Remove bearing (25). Remove snap ring (10) with Tool (D).10. Use Tool (D), and remove snap ring (12) from the housing assembly. Remove bearing (26). Remove snap ring (11) with Tool (D).11. Check all the parts of the turbocharger for damage. If any parts are damaged, use new parts for replacement. See Special Instruction Form No. SMHS6854 for turbocharger reconditioning. Also, see Guidelines For Reusable Parts, Form No. SEBF8018. The following steps are for assembly of the turbocharger.12. Make sure that all the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, put clean engine oil into the oil inlet of the turbocharger.
Make sure the snap rings that hold bearings (25) and (26) in housing assembly (6) are installed with the round edge of the outside diameter toward the bearing.
13. Install snap ring (11) with Tool (D). Install bearing (26). Install snap ring (12) with Tool (D).14. Install snap ring (10) with Tool (D). Install bearing (25). Install snap ring (9) with Tool (D).15. Put wheel assembly (19) in position on Tool (B) with the threaded portion end up.