09300-06610 PUMP ASSY, INJECTI Calibration Data


Rating:
5
Buy PUMP ASSY, INJECTI 09300-06610 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
TRUCK 4D34T7
Engine
4D34T7
Serial start-end
0007-
Info
Injector Nozzle
093500-7500
Injector nozzle: 0935007500

KIT List:

Part name
Kit1
Kit2
Governor assy, mec
Timer assy, automa
Pump assy, fuel fe
Body assy, injecti

Components :

00.001
PUMP ASSY, INJECTI
NB4,R901
01.002
GOVERNOR ASSY, MEC
R901
02.003
LEVER SET
ADJUST L
02.004
COMPENSATOR SUB-AS
01.005
TIMER ASSY, AUTOMA
SB0
01.006
PUMP ASSY, FUEL FE
KS
01.007
BODY ASSY, INJECTI
NB4

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09300-06610
PUMP ASSY, INJECTI
NB4,R901
ME220262 MITSUBISHI
003
[01]
BODY ASSY, INJECTI
NB4
ME736900 MITSUBISHI
004
[01]
GOVERNOR ASSY, MEC
R901
ME743701 MITSUBISHI
005
[01]
TIMER ASSY, AUTOMA
SB0
ME736904 MITSUBISHI
006
[01]
PUMP ASSY, FUEL FE
KS
ME736506 MITSUBISHI
007
[01]
COVER SUB-ASSY, TI
ME743445 MITSUBISHI
008
[01]
O-RING
ID79.5
ME736557 MITSUBISHI
009
[01]
KEY, WOODRUFF
W5,H7.5
ME702920 MITSUBISHI
010
[01]
NUT, TIMER ROUND
ME736909 MITSUBISHI
011
[01]
WASHER, COPPER PLA
T1.5
ME039681 MITSUBISHI
012
[01]
COVER, CONTROL RAC
ME736558 MITSUBISHI
013
[01]
CAP
FOR MAX.SPEED
ME035845 MITSUBISHI
014
[04]
WASHER, STEEL PLAT
FOR M10
MH005068 MITSUBISHI
015
[04]
WASHER, SPRING
M10
MC327716 MITSUBISHI
016
[04]
NUT, HEXAGON
M10
MF430122 MITSUBISHI
017
[02]
BOLT, W/WASHER
M8,L14
ME728977 MITSUBISHI
018
[01]
BOLT, W/WASHER
M8,L22
ME728980 MITSUBISHI
019
[01]
BOLT, W/WASHER
M8,L20
ME728979 MITSUBISHI
020
[04]
BOLT, W/WASHER
M8,L16
ME728978 MITSUBISHI
023
[01]
CAP
FOR FULL-LOAD
ME076458 MITSUBISHI

Include in ##:

09300-06610 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09300-06610 
ME220262 
PUMP ASSY, INJECTI
0930006610 
ME220262 
MITSUBISHI
PUMP ASSY, INJECTI

Test Calibration Data:

0930006610 ME220262




Information:

1. Loosen the clamps on hose (3), remove nuts (2) and remove temperature regulator housing (1) and the gasket from the cylinder head. 2. Remove bolt (5) and the nut from the bracket.3. Remove bolts (6) and (7) that hold the fuel injection lines in position. Remove fuel injection lines (4) from the engine.
Put protection caps (5F2807) and plugs (2F2990) on the injection lines and pumps to keep dirt and foreign material out of the fuel system.
4. Disconnect air lines (8) and (9) from the cylinder head. 5. Remove two locks and bolts (10). Remove the dowel used for location of the rear of the camshafts and remove four bolts (12). Remove valve cover base (11) and the gasket from the cylinder head. 6. Remove bolts (14) that hold cylinder head (13) to the cylinder block. 7. Install four 3/8"-16 NC forged eyebolts in the cylinder head as shown. Fasten a hoist and remove the cylinder head. The weight of the cylinder head is 450 lb. (203 kg).8. Remove the water seals and the head gasket from the spacer plate. 9. Remove the O-ring seal from dowel (16).10. Install six 3/8"-16 NC forcing screws in spacer plate (15). Tighten the screws evenly until the spacer plate is free of the dowels. Remove spacer plate (15).11. Remove the second O-ring seal from dowel (16).Install Cylinder Head And Spacer Plate
A new spacer plate gasket must be installed when the cylinder head is removed.1. Thoroughly clean the top surface of the cylinder block, both surfaces of the spacer plate and the bottom surface of the cylinder head. 2. Put the O-ring seal in position around dowel (1).3. Put a new gasket in position on the cylinder block.
Both surfaces of the spacer plate and the top of the cylinder block must be clean. Do not use a gasket adhesive on these surfaces.
4. Install spacer plate (2) on the cylinder block. 5. Install the O-ring seal on the spacer plate around dowel (1).6. Check the cylinder liner projection. See INSTALL CYLINDER LINERS.7. Put a new cylinder head gasket and water seals in position on the spacer plate. 8. Install two 3/4"-10 NC guide bolts 11 in. long in the cylinder block. Install four 3/8"-16 NC forged eyebolts in the cylinder head. Fasten a hoist and put the cylinder head in position on the guide bolts and lower it on the engine. 9. Put 9M3710 Anti-Seize Compound on the threads of cylinder head bolts (3) and the washer faces. Install bolts (3), the washers and tighten as follows: a) Tighten the bolts in number sequence shown to a torque of 200 lb. ft. (270 N m).b) Tighten the bolts in number sequence shown to a torque of 330 10 lb. ft. (447 14 N m). c) Tighten the bolts in number sequence shown (hand tighten) to a torque of 330 10 lb. ft. (447 14 N m). 10. Put the gasket and valve cover base (4) in position on the

Have questions with 09300-06610?





Group cross 09300-06610

Back to top