09300-00772 PUMP ASSY, INJECTI Denso Cross


Rating:
14
Buy PUMP ASSY, INJECTI 09300-00772 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A4,R801
01.002
BODY ASSY, INJECTI
A4
01.003
GOVERNOR ASSY, MEC
R801 -8802
01.003
GOVERNOR ASSY, MEC
R801 8803-
01.004
TIMER ASSY, AUTOMA
SCZ
01.005
PUMP ASSY, FUEL FE
KS

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09300-00772
PUMP ASSY, INJECTI
A4,R801
ME016193 MITSUBISHI
001
[01]
BODY ASSY, INJECTI
A4:COLD SPEC
ME016132 MITSUBISHI
002
[01]
TIMER ASSY, AUTOMA
SCZ
ME703035 MITSUBISHI
003
[01]
COVER SUB-ASSY, TI
ME703649 MITSUBISHI
004
[01]
O-RING
ID74.1
MH035502 MITSUBISHI
005
[04]
WASHER, STEEL PLAT
FOR M10
MH005068 MITSUBISHI
006
[04]
WASHER, SPRING
M10
MC327716 MITSUBISHI
007
[04]
NUT, HEXAGON
M10
MF430122 MITSUBISHI
008
[01]
GOVERNOR ASSY, MEC
R801
ME703049 MITSUBISHI
009
[01]
PUMP ASSY, FUEL FE
KS
ME703037 MITSUBISHI
010
[01]
CAP
FOR MAX.SPEED
ME035845 MITSUBISHI
013
[01]
KEY, WOODRUFF
T3.985
ME702047 MITSUBISHI
014
[01]
WASHER, COUNTERSUN
T1.5ID14
ME702043 MITSUBISHI
015
[01]
NUT, TIMER ROUND
ME702033 MITSUBISHI
016
[01]
COVER, CONTROL RAC
ME702251 MITSUBISHI
017
[04]
BOLT, W/WASHER
M6,L16
ME702045 MITSUBISHI
018
[01]
BOLT, W/WASHER
M6,L12.5
ME703933 MITSUBISHI
019
[01]
BOLT, W/WASHER
M8,L18
ME703449 MITSUBISHI
022
[01]
CAP
FOR FULL-LOAD
ME076458 MITSUBISHI

Include in ##:

09300-00772 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09300-00772 
ME016193 
PUMP ASSY, INJECTI




Information:

start by:a) remove fuel injection pump housing and governor 1. Install the fuel injection pump housing on tool (A).2. Remove the bolts (1) that hold the governor housing (2) to the fuel injection pump housing.3. Remove the governor housing (2). 4. Remove two springs (4) and the seat (5) from the governor housing.5. Remove the seat (7) from the shaft.6. Remove the spring (6) from the shaft.7. Remove the cover (3) from the pump housing. 8. Remove the shaft (8) and the lever (9) from the pump housing. 9. Remove the thrust collar (11) from the shaft.10. Remove the cover (10) from the pump housing. 11. Loosen the two bolts (13) that hold the torque spring assembly (12) and remove it from the pump housing. 12. Remove the pin (15) from the pump housing.13. Remove the screw (14) and the nut (16) from the pump housing.14. Remove the ring that holds the lever and remove the lever (18) from the dowel (17).15. Remove the dowel (17) from the pump housing. Dowel does not need to be removed unless camshaft is to be removed.
Pull on the shield only a small amount in each location so it will not have distortion or damage. A damaged shield must be replaced.
16. Remove the shield (19) from the camshaft with tool (B). 17. Install the timing pin (C) to hold the camshaft.18. Remove the bolts (20) that hold the flyweight assembly to the camshaft. 19. Remove the flyweight assembly (21) from the camshaft.20. Remove the timing pin (C) from the pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on the bracket assembly (A).2. Install the timing pin (B) to hold the camshaft.3. Put the flyweight assembly (1) in position on the camshaft. Be sure the pin that holds the shaft (2) is in position on the back of the flyweight assembly.4. Install the bolts that hold the flyweight assembly to the camshaft and tighten to a torque of 10 2 lb. ft. (1.38 0.28 mkg).5. Remove the timing pin (B). 6. Put the shield (3) in position over the flyweights. 7. Use the driver (C) to install the shield the remainder of the way on to the camshaft. 8. Put a new O-ring seal on the dowel (4) and install the dowel in the pump housing. Make the dowel even with the machined surface of the counterbore on the outside of the housing. 9. Put the lever (8) on the dowel (4) and install the ring that holds it on the dowel.10. Install the screw (6) and the nut (7) in the pump housing.11. Install the pin (5) in the pump housing. 12. Put the torque spring assembly (10) in position on the housing and tighten the two bolts (11) that hold it to the housing.13. Install the cover (9) on the pump housing. 14. Put the thrust collar (13) in position between the flyweights. Lift the flyweights up with a piece of wire

Have questions with 09300-00772?





Group cross 09300-00772

Back to top