09300-00030 PUMP ASSY, INJECTI Calibration Data


Rating:
1
Buy PUMP ASSY, INJECTI 09300-00030 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
LAND CRUISER 2H
Engine
2H
Serial start-end
8007-
Info
Injector Nozzle
093500-1810
Injector nozzle: 0935001810

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A6,COMB
01.002
BODY ASSY, INJECTI
A6
01.003
GOVERNOR ASSY, COM
COMBINED
01.004
TIMER ASSY, AUTOMA
SCZ
01.005
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09300-00030
PUMP ASSY, INJECTI
A6,COMB
22010-06803 TOYOTA
001
[01]
BODY ASSY, INJECTI
A6
22120-68010 TOYOTA
002
[01]
GOVERNOR ASSY, COM
COMBINED
22320-68030 TOYOTA
003
[01]
PUMP ASSY, FUEL FE
KE
22510-77130 TOYOTA
004
[01]
TIMER ASSY, AUTOMA
SCZ
22610-68010 TOYOTA
007
[01]
COVER, CONTROL RAC
22116-46010 TOYOTA
008
[01]
KEY, WOODRUFF
90099-13020 TOYOTA
009
[01]
NUT, TIMER ROUND
22611-68010 TOYOTA
010
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
011
[04]
BOLT, W/WASHER
M6,L14
90099-04526 TOYOTA
014
[01]
COVER SUB-ASSY, TI
22812-68010 TOYOTA
015
[04]
NUT, HEXAGON
M10
94110-41000 TOYOTA
016
[04]
WASHER, STEEL PLAT
ID10,T4
90201-10018 TOYOTA
018
[01]
BELLOWS ASSY, PNEU
22680-48061 TOYOTA
019
[01]
TUBE, RUBBER
90099-33044 TOYOTA
020
[01]
NUT
M22
90099-05154 TOYOTA
021
[01]
CLIP, CORD
90099-35023 TOYOTA

Include in ##:

09300-00030 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09300-00030 
22010-0680 
PUMP ASSY, INJECTI
0930000030 
22010-06803 
TOYOTA
PUMP ASSY, INJECTI

Test Calibration Data:

0930000030 22010-68030




Information:

Start By:a. remove vibration damper
The crankshaft front seal and wear sleeve come as a set and must be installed as a set. If a replacement of the seal is to be made, a replacement of the wear sleeve must also be made.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use Tool (A) to remove seal (1). 3. Install Tool (C) in the seal bore.4. Install Tool (B) between Tool (C) and wear sleeve (2). Turn Tool (B) until the Tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove Tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Front Seal & Wear Sleeve
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Install the front crankshaft seal and wear sleeve with Tool (A). Use the procedures with follows:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any 6V1541 Quick Cure Primer or 9S3265 Retaining Compound get on the lip of the seal.b. Install locator (3) and bolts (4) on the crankshaft.c. Seal (1) and wear sleeve (2) must be installed dry.
Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (1) as a unit in position on locator (3).e. Put installer (5) in position on locator (3).f. Put clean engine oil on the face of nut (6) and its contact area on installer (5). Install nut (6) on locator (3).g. Tighten nut (6) until the inside surface of installer (5) comes in contact with locator (3).h. Remove Tool (D) from the crankshaft seal and wear sleeve. Tool (D) will install the seal and wear sleeve to the correct depth on the crankshaft.End By:a. install vibration damper

Have questions with 09300-00030?





Group cross 09300-00030

Back to top