09200-03520 PUMP ASSY, INJECTI Denso Cross


Rating:
13
Buy PUMP ASSY, INJECTI 09200-03520 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 6D125
Engine
6D125
Serial start-end
9709-
Info
Injector Nozzle
093500-2710
Injector nozzle: 0935002710

KIT List:

Part name
Kit1
Kit2
Pump assy, fuel fe
Body assy, injecti
Governor assy, mec

Components :

00.001
PUMP ASSY, INJECTI
NB6,RSV -0010
00.001
PUMP ASSY, INJECTI
NB6,RSV 0010-
01.002
PUMP ASSY, FUEL FE
KE
01.003
COUPLING ASSY
SD
01.004
BODY ASSY, INJECTI
NB6
02.005
COVER, BEARING
DUMMY
01.006
GOVERNOR ASSY, MEC
RSV

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09200-03520
PUMP ASSY, INJECTI
NB6,RSV -0010
000
[01]
PUMP ASSY, INJECTI
NB6,RSV 0010-
003
[01]
BODY ASSY, INJECTI
NB6
004
[01]
GOVERNOR ASSY, MEC
RSV
005
[02]
BOLT, W/WASHER
M8,L14
006
[01]
COVER, CONTROL RAC
007
[01]
NUT, TIMER ROUND
008
[01]
WASHER, COUNTERSUN
T1.5ID18
009
[01]
KEY, WOODRUFF
W5,H7.5
010
[01]
PUMP ASSY, FUEL FE
KE22
011
[01]
COVER, PRIMING PUM
012
[01]
WASHER, COPPER PLA
T1.5
014
[01]
COUPLING ASSY
SD
015
[02]
WASHER, FUEL PIPE
T1.2
016
[01]
VALVE ASSY, OVERFL
1.5-1.7K
017
[01]
BOLT, W/WASHER
M8,L20
018
[04]
BOLT, W/WASHER
M8,L16
021
[01]
BOLT, W/WASHER
M8,L22

Include in ##:

09200-03520 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09200-03520 
 
PUMP ASSY, INJECTI




Information:


The impeller shaft nut is a left hand thread (CCW).
(5) Install the compressor wheel (at room temperature) as follows: a. Put compressor wheel on the shaft.b. Put a small amount of clean engine oil on the threads.c. Tighten the nut (CCW) to 14 to 17 N m (125 to 150 lb in).d. Loosen the nut and tighten again to 9 N m (80 lb in) plus an additional 60 degrees (1/6 turn).
Do not bend or add stress to the shaft when the nut is loosened or tightened.
(6) Thickness of each thrust ring ... 2.553 0.013 mm (.1005 .0005 in)(7) Bore in housing (new) ... 20.744 to 20.757 mm (.8167 to .8172 in) Outside diameter of the bearing (new) ... 20.630 to 20.643 mm (.8122 to .8127 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 55 5 N m (40 4 lb ft)Install the band clamps to hold the cartridge to the compressor housing as follows: a. Tighten clamps to 14 1.1 N m (125 10 lb in)b. Tap (hit) clamp lightly all around.c. Tighten again to ... 14 1.1 N m (125 10 lb in) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.

Have questions with 09200-03520?





Group cross 09200-03520

Back to top