09200-02360 PUMP ASSY, INJECTI Calibration Data


Rating:
37
Buy PUMP ASSY, INJECTI 09200-02360 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL W04D
Engine
W04D
Serial start-end
9603-
Info
Injector Nozzle
093500-4450
Injector nozzle: 0935004450

KIT List:

Part name
Kit1
Kit2
Timer assy, automa
Pump assy, fuel fe
Body assy, injecti
Governor assy, mec

Components :

00.001
PUMP ASSY, INJECTI
A4,RSV
01.002
TIMER ASSY, AUTOMA
SCZ
01.003
PUMP ASSY, FUEL FE
KS
01.004
BODY ASSY, INJECTI
A4
01.005
GOVERNOR ASSY, MEC
RSV

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09200-02360
PUMP ASSY, INJECTI
A4,RSV
22030-2710 HINO
000
[01]
09200-02360
PUMP ASSY, INJECTI
A4,RSV
S2203-02710 HINO
003
[04]
NUT, HEXAGON
M10,L8
22825-1490A HINO
004
[01]
VALVE ASSY, OVERFL
1.5-1.8K
22107-1290A HINO
005
[02]
WASHER
T1
22877-1090A HINO
006
[01]
COVER, CONTROL RAC
22114-1020A HINO
007
[04]
WASHER, SPRING
M10
28219-1120A HINO
008
[01]
BOLT, W/WASHER
M6,L14
22815-1480A HINO
009
[01]
COVER SUB-ASSY, TI
22825-1470A HINO
010
[05]
BOLT, W/WASHER
M6,L16
22815-1380A HINO
011
[01]
BOLT, W/WASHER
M8,L22
22815-1190A HINO
013
[04]
WASHER, STEEL PLAT
FOR M10
22877-1551A HINO
014
[01]
NUT, TIMER ROUND
22511-1060A HINO
015
[01]
TIMER ASSY, AUTOMA
SCZ
016
[01]
WASHER, COUNTERSUN
T1.5ID14
22867-1320A HINO
017
[01]
KEY, WOODRUFF
T3.985
22895-1010A HINO
018
[01]
BODY ASSY, INJECTI
A4
021
[01]
PUMP ASSY, FUEL FE
KS
22570-1240A HINO
022
[01]
PLUG
22131-1350A HINO
023
[01]
GOVERNOR ASSY, MEC
RSV

Include in ##:

09200-02360 as PUMP ASSY, INJECTI
09200-02360 PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09200-02360 
22030-2710 
PUMP ASSY, INJECTI
0920002360 
22030-2710 
HINO
PUMP ASSY, INJECTI
0920002360 
S2203-02710 
HINO
PUMP ASSY, INJECTI

Test Calibration Data:

0920002360 22030-2710




Information:

Disassembly and Inspection of Starter
Inspection of Starter
(1) Armature coil short-circuit testPlace the armature on the growler. Set an iron piece parallel to the armature, and rotate the armature slowly by hand. If the iron piece is attracted to the coil or vibrates, there is a short-circuit; replace the armature.
Armature coil short-circuit test(2) Armature coil grounding testIf there is continuity between the commutator and shaft (or core), replace the armature.
Armature coil grounding test(3) Measurement of commutator runoutMeasure the commutator runout using a dial gage. If the amount of runout exceeds the limit value, replace the armature. If the commutator surface is rough, refinish the surface with sand paper (#300 to #500). If the surface has ridges due to abrasion, replace the armature since it is not repairable.
Measurement of commutator runout(4) Measurement of commutator outside diameterMeasure the outside diameter of the commutator, and, if the limit is exceeded, replace the armature.
Measurement of commutator outside diameter(5) Measurement of mold depth between segmentsClean the grooves between segments, and measure the mold depths between segments. If the limit value is exceeded, repair. (6) Inspection of armature gearIf the inspection of the armature gear finds abnormal wearing or chipped teeth, replace the armature.
Measurement of mold depth between segments(7) Yoke coil open-circuit testCheck to see if there is continuity between the terminal lead wire and brush (positive). If there is no continuity, there is an open-circuit; replace the yoke assembly.
Yoke coil open-circuit test(8) Yoke coil grounding testCheck to see if there is continuity between the yoke and brush (positive). If there is continuity, the yoke coil is grounded. Check the insulation, and replace the yoke assembly if the problem cannot be corrected.
Yoke coil grounding test(9) Inspection of magnetic switchConduct the following the following continuity tests, and, if there is any problem, replace the magnetic switch.(a) Coil open-circuit testCheck to see if there is continuity between terminal M and ground (case). There should be no continuity between terminal B and ground.(b) Inspection of contact adhesionCheck to make sure there is no continuity between terminal B and terminal M.
Inspection of magnetic switch(10) Measurement of brush lengthMeasure the length of each brush, and, if the limit value is exceeded, replace the brush. If the brush is unevenly worn or has a rough contact surface, refinish with sand paper (#300 to #500).
Measurement of brush length(11) Measurement of brush spring tensionMeasure the installation tension of each brush spring. Read the tension at the moment when the spring detaches from the brush. If the tension value is near the limit value, replace the brush spring.
Measurement of brush spring tension(12) Inspection of brush holders for insulationUsing a tester, check to make sure that there is no continuity between the positive-side brush holder and negative-side brush holder plate. If there is continuity, replace the brush holder.
Inspection of brush holder for insulation(13) Inspection of overrunning clutchMake sure that the pinion shaft rotates smoothly in one direction, and locks in place when it is turned in the opposite direction. If the pinion shaft does not

Have questions with 09200-02360?





Group cross 09200-02360

Back to top