09200-01470 PUMP ASSY, INJECTI Calibration Data


Rating:
2
Buy PUMP ASSY, INJECTI 09200-01470 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
FH/FK/FM 6D16T2
Engine
6D16T2
Serial start-end
9605-
Info
Injector Nozzle
093500-5160
Injector nozzle: 0935005160

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Governor assy, mec
Timer assy, automa
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
NB6,R901
01.002
BODY ASSY, INJECTI
NB6
02.003
COVER, BEARING
DUMMY
01.004
GOVERNOR ASSY, MEC
R901
02.005
LEVER SET
ADJUST L -9511
02.005
LEVER SET
ADJUST L 9512-
02.006
COMPENSATOR SUB-AS
01.007
TIMER ASSY, AUTOMA
SA2 -9101
01.007
TIMER ASSY, AUTOMA
SA2 9101-
01.008
PUMP ASSY, FUEL FE
KD
01.009
COUPLING ASSY
SD

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
NB6,R901
003
[01]
BODY ASSY, INJECTI
NB6
004
[01]
GOVERNOR ASSY, MEC
R901
005
[01]
TIMER ASSY, AUTOMA
SA2
006
[01]
NUT, TIMER ROUND
007
[01]
COUPLING ASSY
SD
008
[01]
KEY, WOODRUFF
W5,H7.5
009
[01]
PUMP ASSY, FUEL FE
KD
010
[01]
COVER, CONTROL RAC
011
[01]
WASHER, COPPER PLA
T1.5
012
[01]
BOLT, W/WASHER
M8,L20
013
[04]
BOLT, W/WASHER
M8,L16
014
[01]
BOLT, W/WASHER
M8,L22
015
[02]
BOLT, W/WASHER
M8,L14
018
[01]
CAP
FOR MAX.SPEED
019
[01]
CAP
FOR FULL-LOAD

Cross reference number



Part num
Firm num
Firm
Name
09200-01470 
 
PUMP ASSY, INJECTI

Test Calibration Data:

0920001470 ME075677




Information:

Start By:a. remove valve covers 1. Remove bolts (1) that hold the valve cover bases to the cylinder head assembly. Remove valve cover bases (2). 2. Use tool (A) to loosen fuel injection line (3) from fuel injection nozzle (4). 3. Use tool (B) to loosen the nut at the fuel injection line adapter end. Remove inner fuel injection lines (3). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 4. Remove bolts (5) that hold the rocker shaft assemblies to the cylinder head assembly.5. Remove rocker shaft assemblies (6). 6. Put identification marks on the push rods as to their location in the engine. Remove push rods (7). 7. Put identification marks on the bridges as to their location in the engine. Remove bridges (8) from the dowels on the cylinder head assembly.Install Rocker Shaft Assemblies And Push Rods
1. Put clean engine oil on the bridges and dowels. Install the original bridges in their respective locations. New bridges can be mixed.2. Install bridges (8) on the bridge dowels. While firmly pressing 0.5 to 4.5 kg (1 to 10 lb.) straight down on the top contact surface of the bridge, turn the adjusting screw clockwise until contact is made with the valve stem. Turn the screw an additional 20° to 30° (1/3 to 1/2 of 1 hex on nut). This will straighten the dowel in the guide and compensate for the slack in the threads. Hold the adjusting screw in this position, and tighten the locknut to a torque of 30 4 N m (22 3 lb.ft.). Install original push rods in their respective locations in the engine. New push rods can be mixed.3. Install push rods (7). 4. Put rocker shaft assemblies (6) in position on the cylinder head assembly.5. Put clean engine oil on the threads of bolts (5) that hold the shaft assemblies in place. Tighten the bolts first to a torque of 270 25 N m (200 18 lb.ft.). Start with the bolt in the center of the rocker shaft assembly. Tighten the bolts again to a torque of 450 20 N m (330 15 lb.ft.). Tighten the bolts again by hand to a torque of 450 20 N m (330 15 lb.ft.).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (3). Tighten the fuel injection line adapter nuts (9) to a torque of 40 7 N m (30 5 lb.ft.) with tool (B).7. Tighten fuel injection line nut (10) to a torque of 40 7 N m (30 5 lb.ft.) with tool (A).8. Make adjustments to the valves until the intake valve clearance is 0.38 mm (.015 in.) and the exhaust valve clearance is 0.76 mm (.030 in.). See Valve Clearance Setting in Testing And Adjusting. Tighten the locknut to a torque of 30 4 N m (22 3 lb.ft.) and

Have questions with 09200-01470?





Group cross 09200-01470

Back to top