09000-09590 PUMP ASSY, INJECTI Calibration Data


Rating:
60
Buy PUMP ASSY, INJECTI 09000-09590 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
INDUSTRIAL 4D130
Engine
4D130
Serial start-end
8001--8310
Info
Injector Nozzle
093500-1530
Injector nozzle: 0935001530

KIT List:

Part name
Kit1
Kit2
Governor assy, mec
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A4,RSV
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
GOVERNOR ASSY, MEC
RSV
01.004
PUMP ASSY, FUEL FE
KE
01.005
COUPLING ASSY
SP

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
A4,RSV
006
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
007
[01]
GOVERNOR ASSY, MEC
008
[06]
BOLT, W/WASHER
M6,L16
009
[01]
BOLT, W/WASHER
M8,L22
010
[01]
PUMP ASSY, FUEL FE
KE
011
[01]
COUPLING ASSY
SP
012
[01]
COVER, CONTROL RAC
013
[01]
NUT, TIMER ROUND
014
[01]
WASHER, SPRING
ID12.2
015
[01]
KEY, WOODRUFF
016
[01]
COVER, PRIMING PUM

Cross reference number



Part num
Firm num
Firm
Name
09000-09590 
 
PUMP ASSY, INJECTI

Test Calibration Data:

0900009590 61147-51100




Information:

Start By:a. remove flywheel
The crankshaft rear seal and wear sleeve come as a set and must be installed as a set. If a replacement of the seal is to be made, a replacement of the wear sleeve must also be made.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use tool (A) to remove seal (1). 3. Install tool (C) in the seal bore.4. Install tool (B) between tool (C) and wear sleeve (2). Turn tool (B) until the tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Rear Seal And Wear Sleeve
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Install the rear crankshaft seal and wear sleeve with tooling (D). Use the procedure which follows: a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any Quick Cure Primer or Retaining Compound get on the lip of the seal.b. install locator (3) and the bolts on the crankshaft (4).c. The seal and wear sleeve must be installed dry. Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because this type of design, the rear seal group for an engine is different from the front seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (7) as a unit in position on locator (3).e. Put installer (5) in position on locator (3).f. Put clean engine oil on the face of nut (6) and its contact area on installer (5). Install nut (6) on locator (3).g. Tighten nut (6) until installer (5), makes contact with locator (3).h. Remove tooling (D) from the crankshaft seal and wear sleeve. Tooling (D) will install the seal and wear sleeve to the correct depth on the crankshaft.End By:a. install flywheel

Have questions with 09000-09590?





Group cross 09000-09590

Back to top