09000-06023 PUMP ASSY, INJECTI Calibration Data


Rating:
21
Buy PUMP ASSY, INJECTI 09000-06023 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Components :

00.001
PUMP ASSY, INJECTI
A4,MN
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
TIMER ASSY, AUTOMA
SCZ
01.004
PUMP ASSY, FUEL FE
KE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09000-06023
PUMP ASSY, INJECTI
A4,MN
22100-56010 TOYOTA
003
[01]
COVER, CONTROL RAC
M18L19.5
22116-46010 TOYOTA
005
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
22120-56010 TOYOTA
006
[01]
GOVERNOR ASSY, INJ
MN
22310-56010 TOYOTA
007
[01]
PUMP ASSY, FUEL FE
KE
22510-56010 TOYOTA
010
[01]
NUT, TIMER ROUND
D16,L15
22611-46010 TOYOTA
011
[01]
WASHER, SPRING
T3
22173-46010 TOYOTA
012
[01]
SHAFT, SPLINE
22174-47010 TOYOTA
013
[01]
KEY, WOODRUFF
T3.0
90099-13002 TOYOTA
014
[01]
BOLT, W/WASHER
M8,L22
90091-20804 TOYOTA
015
[04]
BOLT, W/WASHER
M6,L16
90091-20611 TOYOTA
016
[01]
BOLT, W/WASHER
M6,L16
90091-20611 TOYOTA
017
[01]
WIRE, OVER, INJECT
22175-56010 TOYOTA
100
[01]
TIMER ASSY, AUTOMA
SCZ
22610-56010 TOYOTA

Include in ##:

09000-06023 as PUMP ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09000-06023 
22100-5601 
PUMP ASSY, INJECTI

Test Calibration Data:

0900006023 22100-56010




Information:


Typical Example1. Remove bolts (1) and cover (2). Remove bolts (3) and cover (4).
Typical Example2. Remove bolts (5) and adapter (6). Be sure that gear stays in place. Remove bolts (7) and cover (8). Keep gear in place.
Typical Example3. Remove gears (9) and crankshaft gear (10). Remove bolts (11) and idler gear (12) with retainer. Remove bolts (13) and idler gear (14) with retainer.
Typical Example4. Secure strap and a hoist to housing (15). Remove hose assembly (16) and small bolts (17) and large bolts (18). 5. Remove bolts (19) that connect housing to oil pan (20). Remove housing from cylinder block. The weight of housing is approximately 105 kg (230 lb). 6. Check O-ring seal (21) and bearing (22) on adapter and replace if necessary. 7. Check bearing (23) and O-ring seal (24) on cover and replace if necessary. 8. Remove retainer (25) from gear (9) and check bearings (26) and replace if necessary. The following steps are for the installation of the flywheel housing.9. Thoroughly clean the contact surfaces of the cylinder block and flywheel housing. Install a new gasket between the flywheel housing and the cylinder clock.10. Secure strap and a hoist to the flywheel housing, put flywheel housing in position on the cylinder block. 11. Install the bolts that hold the flywheel housing to the cylinder block. Tighten bolts 1 thru 22 in number sequence to a torque of 40 10 N m (30 7 lb ft). Tighten bolts 1 thru 9 in number sequence again to a torque of 135 20 N m (100 15 lb ft). Tighten bolts 10 thru 22 in number sequence again to a torque of 55 10 N m (40 7 lb ft).12. Install bolts that connect housing to oil pan.13. Cut flywheel housing gasket off even with the cylinder block surface. Remove excess sealant.End By:a. install crankshaft rear seal and wear sleeveb. install starting motor

Have questions with 09000-06023?





Group cross 09000-06023

Back to top