09000-02880 PUMP ASSY, INJECTI Denso Cross


Rating:
4
Buy PUMP ASSY, INJECTI 09000-02880 genuine, new aftermarket engine parts with delivery

Information pump assy, injecti Denso

Product
Fuel Injection Pump
Vehicle engine
Construction machine F4L812D
Engine
F4L812D
Serial start-end
6910--7001
Info
Injector Nozzle

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Pump assy, fuel fe

Components :

00.001
PUMP ASSY, INJECTI
A4,RSV
01.002
BODY ASSY, INJECTI
A4:DRIV.16.8
01.003
PUMP ASSY, FUEL FE
KS22

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
PUMP ASSY, INJECTI
A4,RSV
004
[01]
SCREW, HOLLOW
M14,L10
008
[01]
GOVERNOR ASSY, MEC
RSV
009
[01]
PUMP ASSY, FUEL FE
KS
010
[01]
BODY ASSY, INJECTI
A4:DRIV.16.8
011
[01]
NUT, HEXAGON
M12
012
[01]
WASHER, SPRING
T2.5
013
[01]
KEY, WOODRUFF
015
[01]
COVER, CONTROL RAC
016
[01]
WASHER, COPPER PLA
T1
017
[04]
WASHER, FUEL PIPE
-9410
017
[04]
WASHER, FUEL PIPE
ID13.8 9411-
018
[01]
VALVE ASSY, OVERFL
1.8K
019
[01]
SCREW, AIR BLEEDER
020
[06]
SCREW, SLOTTED OVA
021
[01]
BOLT, W/WASHER
M8,L22

Cross reference number



Part num
Firm num
Firm
Name
09000-02880 
 
PUMP ASSY, INJECTI




Information:

The 5P-4150 Tester Group is used for testing:* Capsule-Type Fuel Valves* Pencil-Type Fuel Nozzles* Caterpillar Direct Injection Fuel Nozzles The additional tools referenced in this manual are needed for testing or cleaning specific fuel valves and nozzles or are part of 8S-2245 Cleaning Tool Group. These tools are available from the Parts Department. The 8T-0860 and 8T-0856 Pressure Gauges, 1U-9578 Repair Kit (not shown), 8T-5313 Nozzle Test Filter (1), and 6V-0183 Pump Body Gasket (2) are all available from the Parts Department.Install a new 8T-5313 Nozzle Tester Filter (1) at least once every three months, or more often when necessary. Install a new 6V-0183 Pump Body Gasket (2) when necessary. For nozzle cleaning procedure, refer to Special Instruction SEHS8627 entitled "Use Of 8S2245 Nozzle Cleaning Tool Group".Reference: Service Manual Parts Book, Special Instruction SEHS8627 "Use of 8S2245 Nozzle Cleaning Tool Group", SEHS7390 "Test Sequence For Pencil-Type Fuel Nozzles".General Information
When testing either new nozzles or nozzles that are not suspected of a failure, it is permissible to flush each nozzle three full strokes before the test.It is necessary to have an accurate record of the test results for each nozzle that is tested. Record the results of each nozzle test procedure on SEHS8144 "Nozzle Test Record".These test sheets are available through Miscellaneous Order Division. Pads containing 50 sheets may be ordered with special instruction SEHS8144. A copy of SEHS8144 is shown at the back of this manual. Always keep the reservoir filled with CLEAN calibration fluid. Low oil level will cause SOFT or SPONGY operation of the tester pump. Use SAE J-967 Calibration Fluid in the tester. Order calibration fluid, according to the amount needed, by the following part numbers.6V-6067 Calibration Fluid...208 L (54.9 gal U.S.) Drum6V-6068 Calibration Fluid...19 L (5.0 gal U.S.) Pail9U-7411 Calibration Fluid...3.8 L (1.0 gal U.S.) PailHave the pressure gauges checked and calibrated at least once each year. Checking and calibration should be performed more often if the test results become inconsistent of inaccuracy is suspected. There are two methods for gauge calibration. Gauge calibration should be checked using the 5P-8558 Pressure Gauge Calibrating Group or calibrated by the gauge manufacture.This manual contains the instructions for gauge calibration when using 5P-8558 Pressure Gauge Calibrating Group. This Manual also contains the procedures to follow if the gauges are sent to the manufacturer for calibration.Refer to "Calibration (Method 1 or Method 2)" in this manual.The rate of 8T-0856 Pressure Gauge is 0-6000 kPa (0-870 psi) with minor divisions (increments) of 100 kPa (20 psi).The range of 8T-0860 Pressure Gauge is 0-40 000 kPa (0-5800 psi) with minor divisions (increments) of 1000 kPa (100 psi).The accuracy for either gauge is 2.0 percent full scale across the entire readable range.The test information in this manual has been obtained by comparison tests of fuel nozzles known to be good. These tests are not intended to be a duplication of conditions that exist during engine operation.The tests in this manual will provide an indication of nozzle condition. A nozzle that

Have questions with 09000-02880?





Group cross 09000-02880

Back to top