19089-00740 OVER-HAUL KIT, GOV Denso Cross


Rating:
32
Buy OVER-HAUL KIT, GOV 19089-00740 genuine, new aftermarket engine parts with delivery

Information over-haul kit, gov Denso

Product
Fuel Injection Pump
Vehicle engine
COMMON
Engine
Serial start-end
Info
R901
Injector Nozzle

Components :

00.001
OVER-HAUL KIT, GOV
R901H

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19089-00740
OVER-HAUL KIT, GOV
R901H
001
[01]
GASKET, PUMP BODY
002
[01]
GASKET, COVER
-0903
002
[01]
GASKET, COVER
0903-
003
[01]
GASKET
004
[02]
O-RING
ID39.5
005
[01]
O-RING
ID 7.5
006
[02]
WASHER, DRAIN SCRE
T1.0
007
[01]
O-RING
ID54.5 -9911
007
[01]
GASKET
51X51 MM 9912-
008
[01]
O-RING
ID52.5 -9911
008
[01]
GASKET
54X42 MM 9912-
009
[06]
E-RING
D11,T0.7
010
[06]
DAMPER, FLYWEIGHT
011
[01]
SEAL, OIL
012
[01]
O-RING
ID45.5

Include in ##:

19089-00740 as OVER-HAUL KIT, GOV

Cross reference number



Part num
Firm num
Firm
Name
19089-00740 
 
OVER-HAUL KIT, GOV

Use as kit:

Assy
Denso
Part name
Kit1
Kit2
Governor assy, mec
1908900740  
 
Governor assy, mec
1908900740  
 
Governor assy, mec
1908900740  
 
Governor assy, mec
1908900740  
 
Governor assy, mec
1908900740  
 
Governor assy, mec
1908900740  
 




Information:


Illustration 1 g01340837
Illustration 2 displays mounting the Diesel Particulate Filter Monitor System to the ECM.
Illustration 2 g01340267
Table 1
Power Supply Requirements    
Requirements for 12 VDC or 24 VDC system     Value     Notes    
Operating Minimum Voltage     +9V     Minimum continuous operating voltage without damage to the ECM    
Operating Minimum Voltage     +32V     Maximum continuous operating voltage without damage to the ECM    
Overvoltage Maximum (two minutes continuous)     +80V     At 25 °C (77 °F)    
Reverse Voltage (one hours)     -32V    
85 °C (185 °F)    
power up voltage for the ECM     +9V     Minimum voltage for the ECM in order to run internally. Operating the engine at this voltage will cause damage to the ECM.    
Cranking Voltage            
Maximum current draw with key switch off     10mA        
Maximum current draw with 0 engine speed and no loads being driven     500mA        
Maximum continuous operating current draw     10A     This is highly dependent upon the number and type of loads driven by the ECM.    
Recommended Battery Fuse size     15A        Programming For The ECM
The ECM is flash programmed via the Customer Data Link (CDL) with the service tool.Key Switch For The ECM
The ECM Key Switch provides the ability to shut down the ECM via a low current switch. The ECM Key Switch also increases the life of the batteries by shutting the ECM off. The Key Switch also allows operators to remotely power off the ECM. The Key Switch controls when the ECM powers up. With the Key Switch "OFF", the ECM current draw will not exceed 10mA.Connector For The ECM
The ECM uses a 70 pin connector to connect to the OEM vehicle wiring harness. The ECM Connector Screw torque should be 6 1 N m (4 0.7 lb ft)Connector Wire Gauge Size For The ECM
The battery positive and negative connections must be made with 14 gauge SAE J1128 type GXL wire for the Deutsch stamped and formed terminal or the Deutsch solid terminal. All other connections may be16 gauge or 18 gauge SAE J1128 type SXL or 14, 16 or 18 gauge SAE J1128 type GXL (or equivalent wire).For most components on the engine an 18 gauge wire has sufficient current capacity, however, many applications will benefit from the increased reliability and durability of 16 gauge wire.Connector Terminals and Sealing Plugs For The ECM
Table 2 provides terminal and plug part numbers. All terminals used in this connector must be gold or selective gold flash terminals.
Table 2
Description     Usage    
70 Terminal Plug, Keyed 2     ECM Connector Harness    
Sealing Plug 14 - 18 gauge     Unused Connector Slots    

Have questions with 19089-00740?





Group cross 19089-00740

Back to top